One thing that is found in virtually every industrial environment is an air compressor. Some uses for the compressed air generated are: powering pneumatic tools, packaging, automation equipment, conveyors, controls systems, and various others. Pneumatic tools are favored because they tend to be smaller and more lightweight than electric tools, offer infinitely variable speed and torque, and can be safer than the hazards associated with electrical devices. In order to power these devices, compressed air must be generated.
There are two main categories of air compressors: positive-displacement and dynamic. In a positive-displacement type, a given quantity of air is trapped in a compression chamber. The volume of which it occupies is mechanically reduced (squished), causing a corresponding rise in pressure. In a dynamic compressor, velocity energy is imparted to continuously flowing air by a means of impellers rotating at a very high speed. The velocity energy is then converted into pressure energy.
Of the positive-displacement variety they are broken down further into two more categories: reciprocating and rotary. A reciprocating compressor works like a bicycle pump. A piston reduces the volume occupied by the air or gas, compressing it into a higher pressure. There are two types of reciprocating compressors, single or double-acting. Single-acting compressors are the most common and are available up to 30HP at 200 psig. Their small size and weight allow them to be installed near the point of use and avoid lengthy piping runs. These are the types of compressors that would be commonly found in your garage. The double-acting reciprocating compressor is much like its single-acting brethren, only it uses both sides of the piston and cylinder for air compression. This doubles the capacity of the compressor for a given cylinder size. They are much more efficient than single-acting compressors, but are more expensive and do require a more specialized installation and maintenance.
Rotary compressors are available in lubricant-injected or lubricant-free varieties. These types of compressors use two inter-meshing rotors that have an inlet port at one end and a discharge port at the other. Air flows through the inlet port and is trapped between the lobes and the stator. As the rotation continues, the point intermeshing begins to move along the length of the rotors. This reduces the space that is occupied by the air, resulting in an increase in pressure. In the lubricant-injected compressors, the compression chamber is lubricated between the intermeshing rotors and bearings. This takes away the heat of compression and also acts as a seal. In the lubricant-free varieties, the intermeshing rotors have very tight tolerances and are not allowed to touch. Since there is no fluid to remove the heat of compression, they typically have two stages of compression with an intercooler between and an after cooler after the second stage. Lubricant-free compressors are beneficial as they supply clean, oil-free compressed air. They are, however, more expensive and less efficient to operate than the lubricant-injected variety.
On the other side of the coin, we have the dynamic compressors. These are comprised of two main categories: axial and centrifugal. These types of compressors raise the pressure of air or gas by imparting velocity energy and converting it to pressure energy. In a centrifugal air compressor, air continuously flows and is accelerated by an impeller. This impeller can rotate at speeds that exceed 50,000 rpm. Centrifugal air compressors are generally much larger and can accommodate flow ranges of 500-100,000 CFM. They also provide lubricant-free air.
Axial compressors are used for situations that require lower pressure but high flow rates. They do not change the direction of the gas, it enters and exits the compressor in an axial direction. It is accelerated and then diffused which creates the increase in pressure. A common application that would be served by this type of compressor is to compress the air intake of gas turbines. They have a relatively high peak efficiency, however their large overall size and weight as well as the high starting power requirements pose some disadvantages.
Of course, any of these types of compressors can be used to supply air to your engineered Intelligent Compressed Air Products. If you have an application in your facility that could benefit from an engineered solution, give us a call. An Application Engineer would be happy to discuss your options with you and see to it that you’re getting the most out of your compressed air!
Image courtesy of Compressor1 via Creative Commons License