Tag: control receiver

Removing Condensation Is Key To Maintaining Performance

Published on by exaircorpLeave a comment

When air is compressed, it is heated to a point that causes the water or moisture  to turn to vapor. As the air begins to cool, the vapors turn to condensation, which can cause performance issues in a compressed air system. Many times this condensation forms in the basic components in the system like a receiver tank, dryer or filter.

Condensation is formed from water vapor in the air

It’s important to remove this condensation from the system before it causes any issues. There are four basic types of condensate drains that can be used to limit or prevent loss of air in the system.

The first method would be to have an operator manually drain the condensation through a drain port or valve. This is the least reliable method though as now it’s the operator’s responsibility to make sure they close the valve so the system doesn’t allow any air to escape which can lead to pressure drops and poor end-use device performance.

Example of a float drain

Secondly, a float or inverted bucket trap system can be used in plants with regular monitoring and maintenance programs in place to ensure proper performance.. These types of drain traps typically require a higher level of maintenance and have the potential to lose air if not operating properly.

An electrically actuated drain valve can be used to automatically drain the condensate at a preset time or interval. Typically these incorporate a solenoid valve  or motorized ball valve with some type of timing control.  These types of systems can be unreliable though as the valve may open without any moisture being present in the line, which can result in air loss or it may not be actuated open long enough for acceptable drain off. With these types of drains, it’s best to use some type of strainer to remove any particulate that could cause adverse performance.

Lastly,  zero air-loss traps utilize a reservoir and a float or level sensor to drain the condensate and maintain a satisfactory level. This type of setup is very reliable but does require the reservoir be drained frequently to keep the system clean and free of debris or contaminants.

If you have any questions or would like to discuss a particular process, contact an application engineer for assistance.

Justin Nicholl
Application Engineer
justinnicholl@exair.com
@EXAIR_JN

 

Condensation image courtesy of Anders Sandberg via creative commons license

Float drain image courtesy of the Compressed Air Challenge

What Makes A Compressed Air System “Complete”?

Published on by Lee EvansLeave a comment

It’s a good question.  When do you know that your compressed air system is complete?  And, really, when do you know, with confidence, that it is ready for use?

A typical compressed air system. Image courtesy of Compressed Air Challenge.

Any compressed air system has the basic components shown above.  A compressed air source, a receiver, dryer, filter, and end points of use.   But, what do all these terms mean?

A compressor or compressed air source, is just as it sounds.  It is the device which supplies air (or another gas) at an increased pressure.  This increase in pressure is accomplished through a reduction in volume, and this conversion is achieved through compressing the air.  So, the compressor, well, compresses (the air).

A control receiver (wet receiver) is the storage vessel or tank placed immediately after the compressor.  This tank is referred to as a “wet” receiver because the air has not yet been dried, thus it is “wet”.  This tank helps to cool the compressed air by having a large surface area, and reduces pulsations in the compressed air flow which occur naturally.

The dryer, like the compressor, is just as the name implies.  This device dries the compressed air, removing liquid from the compressed air system.  Prior to this device the air is full of moisture which can damage downstream components and devices.  After drying, the air is almost ready for use.

To be truly ready for use, the compressed air must also be clean.  Dirt and particulates must be removed from the compressed air so that they do not cause damage to the system and the devices which connect to the system.  This task is accomplished through the filter, after which the system is almost ready for use.

To really be ready for use, the system must have a continuous system pressure and flow.  End-use devices are specified to perform with a required compressed air supply, and when this supply is compromised, performance is as well.  This is where the dry receiver comes into play.  The dry receiver is provides pneumatic capacitance for the system, alleviating pressure changes with varying demand loads.  The dry receiver helps to maintain constant pressure and flow.

In addition to this, the diagram above shows an optional device – a pressure/flow control valve.  A flow control valve will regulate the volume (flow) of compressed air in a system in response to changes in flow (or pressure).  These devices further stabilize the compressed air system, providing increased reliability in the supply of compressed air for end user devices.

Now, at long last, the system is ready for use.  But, what will it do?  What are the points of use?

Points of use in a compressed air system are referred to by their end use.  These are the components around which the entire system is built.  This can be a pneumatic drill, an impact wrench, a blow off nozzle, a pneumatic pump, or any other device which requires compressed air to operate.

If your end use devices are for coating, cleaning, cooling, conveying or static elimination, EXAIR Application Engineers can help with engineered solutions to maximize the efficiency and use of your compressed air.  After placing so much effort into creating a proper system, having engineered solutions is a must.

Lee Evans
Application Engineer
LeeEvans@EXAIR.com
@EXAIR_LE