Tag: storage tank

6 STEPS To Optimizing Compressed Air: Step 5 – Install Secondary Receiver Tanks

Published on by johnball2014Leave a comment

Since air compressors require electricity to make compressed air, it is important to optimize your compressed air system. EXAIR has six simple steps, and following these steps will help you cut electrical costs, reduce overhead, and improve your bottom line.  In this blog, I will cover the fifth step –intermediate storage of compressed air near the point-of-use. 

I had a customer that was looking at a model 1122108, 108” (2,743mm) Super Ion Air Knife Kit.  The application was removing static and debris from insulated panels which they used for large refrigerated trailers.  They were worried about how much compressed air that it would use; and they were considering a blower-type system.  I went through the negative aspects like noise, cost, maintenance, and ineffectiveness with turbulent air flows.  But, when you are limited in the amount of compressed air, I had to look at another way.  Since the process was intermittent, I used the fifth step to optimize their system to use a much better solution for their application.  The cycle rate was 2 minutes on and 10 minutes off.  I was able to calculate the size of a secondary tank to help their compressed air system.   

Model 9500-60

I would like to expand a bit more about secondary receiver tanks.  They can be strategically placed throughout the plant to improve the “ebbs and flows” of pneumatic demands.  The primary receiver tanks help to protect the supply side when demands are high, and the secondary receiver tanks help pneumatic systems on the demand side.  They give additional capacity at the end of distribution lines.  Essentially, it is easier and more efficient for compressed air to travel out from a nearby source and into an application rather than traveling through long lengths of pipes from the distribution system.

For calculating the volume size for your secondary receiver tank, we can use Equation 1 below.  It is the same for sizing a primary receiver tank, but the scalars are slightly different.  The supply line for air drops will typically come from a header pipe and are generally smaller in diameter.  So, we have to look at the air restriction that can feed into the tank.  For example, a 1” NPT Schedule 40 Pipe at 100 PSIG can supply a maximum of 150 SCFM of air flow.  This value is used for Cap below in Equation 1.  C is the largest air demand for the machine or targeted area that will be using the tank.  If the C value is less than the Cap value, then a secondary tank is not needed.  If the Cap is below the C value, then we can calculate the tank volume that would be needed.  The other value in the equation is the minimum tank pressure.  In most cases, a regulator is used to set the air pressure for the machine or area.  If the specification is 80 PSIG, then you would use this value as P2.  P1 is the header pressure that will be coming into the secondary tank.  With this collection of information, you can use Equation 1 to calculate the minimum tank volume. 

Equation 1:

V = T * (C – Cap) * (Pa) / (P1-P2)

Where:

V – Volume of receiver tank (cubic meter)

T – Time interval (minutes)

C – Air demand for system (cubic meter per minute)

Cap – Supply value of inlet pipe (cubic meter per minute)

Pa – Absolute atmospheric pressure (Bar)

P1 – Header Pressure (Bar)

P2 – Regulated Pressure (Bar)

For this customer above, I am still working on this purchase.  But we went from a “we don’t have enough compressed air” to a “we can possibly use the better solution with the Super Ion Air Knife”.  If you find that you might be having issues with your equipment running optimally, you may be able to install a secondary receiver to your system.  EXAIR offers 60 Gallon tanks, model 9500-60, to add to those specific areas.  If you have any questions about using a receiver tank in your application, primary or secondary, you can contact an Application Engineer at EXAIR.

John Ball
Application Engineer
Email: johnball@exair.com
Twitter: @EXAIR_jb

Compressed air Storage: Do you need a Receiver Tank?

Published on by Jordan T ShouseLeave a comment

Maintaining a “supply and demand” balance in the design & operation of compressed air systems often includes receiver tanks.

Just like in economics, we have to consider both sides – supply AND demand – to best maintain this balance.  Also like in economics, there are numerous factors…on both sides…but the two most critical factors are:

  • Compressor capacity control (supply side)
  • System storage (demand side)

I wrote a blog on “Air Compressor Motors and Controls, Working Together”, outlining the ‘supply side’ variables, today lets look at the system storage. Distribution piping makes up a certain amount of this, and another great blog from my colleague, Tyler Daniel – “Intelligent Compressed Air: Distribution Piping and Pressure Drop” – gets me off the hook for THAT part of the discussion today.

We can consider the air capacity of system piping to be fixed for the purposes of this discussion, so our “variable” will be the capacity of storage tanks. Let’s start with the reasons for the need for system storage: Strategically placed point-of-use air receivers provide stored energy for intermittent demands.  This enables the compressed air system to handle fluctuating loads, efficiently & reliably.  It also minimizes impact (e.g., sudden and often detrimental drops) on the system pressure.

Next, we’ll look at location. There are a couple of common options to consider:

  • The intermittent demand. Installing a receiver here will provide enough air for short duration, high consumption events, protecting the rest of the system from pressure excursions. Dedicating the receiver to this application will mean isolating it from the rest of the system with a check valve (so it only supplies the load in question) and a needle valve (so recharging the receiver itself, between the intermittent uses, doesn’t adversely affect total system pressure).
  • The critical load(s). Instead of using stored air for the intermittent load, you can also use it for the important loads you’re trying to protect. All sorts of machinery with pneumatic components can “crash” if a nearby intermittent demand starts up & “steals” their air. You’ll use a check valve (same as above), but using a needle valve to throttle the air flow that recharges the receiver risks “starving” the critical load. Don’t do that unless there’s a really good (and likely really specific) reason for it.

Finally, we’re going to do some math, so we know how big this receiver has to be. Here’s the equation we use to do that:

Let’s calculate the receiver size needed to supply an intermittent load of 400 SCFM (C) @80psig (P2), that’ll run for one minute (T). You can use data specific to your system to come up with a value for (Cap) but here I’m going to assume we want the receiver to be able to handle the whole thing, so Cap = 0. I’m also going to assume we’re at sea level, so Pa = 14.7psia and that our compressor’s discharge pressure (the pressure at which the receiver can be charged to) is 120psig (P1):

That’s an awfully big tank. Now, let’s calculate the receiver size needed to protect a critical load that uses 55 SCFM @60psig, and that due to the system design, we can count on 25 SCFM @120psig from the compressor:

This is a much more manageable size, in fact, our 60 Gallon Receiver Tank (Model 9500-60) would be ideal. It’s 20″ in diameter and just over 50″ tall, so it doesn’t take up a lot of floor space. It comes with a drain valve and connections for compressed air flow in & out, pressure gauge, relief valve, etc.

Step Five of our Six Steps To Optimizing Your Compressed Air System: Use intermediate storage near the point of use.

Now, the above example is a completely hypothetical situation, and I purposely chose exaggerated values to show that there can indeed be a clear “winner” in the choice between the two installation points. If you have a situation like this, and would like help in finding the solution that makes the most sense, give us a call.

Jordan Shouse
Application Engineer

Send me an Email
Find us on the Web 
Like us on Facebook
Twitter: @EXAIR_JS

How To Determine The Need For – And The Size Of – Compressed Air Receiver Tanks

Published on by Russ BowmanLeave a comment

Supply and Demand, in economics, defines the relationship between the volume of commodities that sellers want to exchange for a certain amount of currency, and the volume of said commodities that buyers are willing to exchange a certain (and sometimes different) amount of currency for.  The best chance for an ideal condition is when the volume produced is the same as the volume being consumed.  That typically means both sides are amenable to the same certain amount of currency, and everyone’s happy: the sellers are making a fair profit, and the buyers are paying a fair price.  Thing is, that’s a difficult balance to maintain.  The reasons for imbalances are often debated and usually contentious, and I have no intention of going in to them here.  I only brought up the subject to draw an analogy to the difficulties in maintaining a “supply and demand” balance in the design & operation of compressed air systems.

Just like in economics, we have to consider both sides – supply AND demand – to best maintain this balance.  Also like in economics, there are numerous factors…on both sides…but the two most critical factors are:

  • Compressor capacity control (supply side)
  • System storage (demand side)

My colleague Jordan Shouse wrote an excellent blog on “Air Compressor Motors and Controls, Working Together”, outlining the ‘supply side’ variables, allowing me to concentrate my efforts today on system storage. Distribution piping makes up a certain amount of this, and another great blog from another colleague, Tyler Daniel – “Intelligent Compressed Air: Distribution Piping and Pressure Drop” – gets me off the hook for THAT part of the discussion today.

We can consider the air capacity of system piping to be fixed for the purposes of this discussion, so our “variable” will be the capacity of storage tanks. Let’s start with the reasons for the need for system storage: Strategically placed point-of-use air receivers provide stored energy for intermittent demands.  This enables the compressed air system to handle fluctuating loads, efficiently & reliably.  It also minimizes impact (e.g., sudden and often detrimental drops) on the system pressure.

Next, we’ll look at location. There are a couple of common options to consider:

  • The intermittent demand. Installing a receiver here will provide enough air for short duration, high consumption events, protecting the rest of the system from pressure excursions. Dedicating the receiver to this application will mean isolating it from the rest of the system with a check valve (so it only supplies the load in question) and a needle valve (so recharging the receiver itself, between the intermittent uses, doesn’t adversely affect total system pressure).
  • The critical load(s). Instead of using stored air for the intermittent load, you can also use it for the important loads you’re trying to protect. All sorts of machinery with pneumatic components can “crash” if a nearby intermittent demand starts up & “steals” their air. You’ll use a check valve (same as above), but using a needle valve to throttle the air flow that recharges the receiver risks “starving” the critical load. Don’t do that unless there’s a really good (and likely really specific) reason for it.

Finally, we’re going to do some math, so we know how big this receiver has to be. Here’s the equation we use to do that:

Let’s calculate the receiver size needed to supply an intermittent load of 400 SCFM (C) @80psig (P2), that’ll run for one minute (T). You can use data specific to your system to come up with a value for (Cap) but here I’m going to assume we want the receiver to be able to handle the whole thing, so Cap = 0. I’m also going to assume we’re at sea level, so Pa = 14.7psia and that our compressor’s discharge pressure (the pressure at which the receiver can be charged to) is 120psig (P1):

That’s an awfully big tank. Now, let’s calculate the receiver size needed to protect a critical load that uses 55 SCFM @60psig, and that due to the system design, we can count on 25 SCFM @120psig from the compressor:

This is a much more manageable size, in fact, our 60 Gallon Receiver Tank (Model 9500-60) would be ideal. It’s 20″ in diameter and just over 50″ tall, so it doesn’t take up a lot of floor space. It comes with a drain valve and connections for compressed air flow in & out, pressure gauge, relief valve, etc.

Step Five of our Six Steps To Optimizing Your Compressed Air System: Use intermediate storage near the point of use.

Now, the above example is a completely hypothetical situation, and I purposely chose exaggerated values to show that there can indeed be a clear “winner” in the choice between the two installation points. “Your mileage may vary,” as the car folks say. If you have a situation like this, and would like help in finding the solution that makes the most sense, give me a call.

Russ Bowman, CCASS

Application Engineer
EXAIR Corporation
Visit us on the Web
Follow me on Twitter
Like us on Facebook

Cover image courtesy of: Tennessee Valley Authority; SVG version by Tomia, CC BY-SA 3.0 <http://creativecommons.org/licenses/by-sa/3.0/>, via Wikimedia Commons