Issues and Problems with Pressure Drop

 

Super Air Knife Install Sheet

Pressure drop comes in different forms, and it causes inefficiencies within your pneumatic system.  EXAIR writes statements in the installation manuals to help find the correct pipe sizes to supply the different products.  (Reference Super Air Knife Installation Manual above).   But there are other areas that can affect the performance.  These can be fittings, tubing, valves, and accessories.  In this blog, I will cover some pitfalls that can minimize the potential of your EXAIR products.

Pressure drop by definition is a difference or loss in pressure.  A properly sized Filter Separator will typically have a pressure drop of 5 PSID (0.3 bar) at the rated conditions.  So, if you start with 100 PSIG (6.9 bar), the air pressure after the filter separator will be 95 PSIG (6.6 bar).  But what happens when a filter separator is undersized or too small?  The pressure drop will be much higher.  So, if the pressure drop is 30 PSID (2 bar), then the downstream air pressure will only be 70 PSIG (4.8 bar).  At that pressure, you may not be able to get the performance that is required to do the job.

The first thing in determining these potential issues is what I like to call forensics.  If you can install a pressure gage at the inlet of any EXAIR product, then you can deduce if a potential problem is within your setup.   For example, if the Pressure Regulator is at 100 PSIG (6.9 bar), and the pressure gauge at the inlet is reading only 60 PSIG (4.1 bar), then there is a pressure drop of 40 PSID (2.8 bar) between these two points.  You can look in this area for the problem or problems.  If the gauge on the Pressure Regulator goes down as well when you are operating, then the problem area is upstream of the Pressure Regulator.  This can be from the pipe size or the air compressor.

The most common issues are fittings and tubing.  With fittings, small openings may not allow enough air to pass through.  Above is a photo of some typical fittings.  You notice that the right side of the chart has large enough openings to decrease pressure drop.  In some instances, quick connect fittings are commonly used to easily connect or disconnect pneumatic devices; but if you use too small or too many of these fittings, they can cause a large pressure drop.

The other problem is with the inner diameter of tubing, hoses, or pipes that are not properly sized.  Russ Bowman, a colleague, created a video showing the issues with improperly sized plumbing.  It is a very interesting video that shows the effect on a Super Air Knife.

If you want to get the most from your EXAIR products, you will need to reduce the amount of pressure drop in your system.  Pressure drop is wasted energy and can affect your pneumatic system.  You can follow my recommendations above.  Or if you would like to discuss your setup with an Application Engineer, we will be happy to assist.

John Ball
Application Engineer

Email: johnball@exair.com
Twitter: @EXAIR_jb

Custom Solutions For Conveying Dry Material

The ideal solution for conveying large volumes of material over long distances.

EXAIR’s Line Vac compressed air operated conveyors have no moving parts or motors to wear out, providing a maintenance free way to move dry material from one location to another. We offer several different types and sizes of Line Vacs like our Standard Line Vacs, available from 3/8″ up to 5″  or our Threaded Line Vacs, with NPT threaded connections up to 3″. The Heavy Duty Line Vac are constructed of Hardened Alloy for superior abrasion resistance, available in sizes from 3/4” to 3”, smooth and threaded connections or the Light Duty Line Vac commonly used for smaller volume, shorter distance processes, with sizes from 3/4″ to 6”. We even offer Sanitary Flange Line Vacs from 1-1/2″ up to 3″ for processes requiring frequent cleaning. All of these products are in stock, ready to ship from our factory here in Cincinnati, Ohio.

For over 34 years, EXAIR has been manufacturing Intelligent Compressed Air Products and we understand that there may be “special” cases where a stock product isn’t going to fit a specific need or requirement. What sets us apart from our competition is that we are able, with a little help from the customer, to engineer and manufacture custom made products, like the Line Vac Conveyors, to fit the specific demand of a unique application.

A few examples are shown below:

Flanged design, easy to install


This special 3/4″ Stainless Steel flanged Line Vac is being used to remove acidic vapors after a silicon wafer etching process. The flanged design allowed the user to direct mount to the machine, eliminating the need for other expensive modifications.

 

 

 

Chemical resistant construction for washdown areas

 

 

A customer was needing a special Line Vac for a chloride wash area due to the aggressive chemicals. We were able to make a custom 1-1/2″ Line Vac in PVDF construction for corrosion resistance and QF flanges for easy maintenance and cleaning.

 

 

 

Custom funnel design for small, granulated material like sugar or salt

 

This special funnel shaped Line Vac is being used in a a small packet filling operation. The unique design assured for a clog free process by keeping the granulated material moving through the tube.

 

 

 

 

 

Miniature size for confined workspaces

 

A company was needing a miniature version of a Line Vac to remove microscopic debris in an integrated circuit chip making process. The barb fittings allowed for easy installation into the small work place.

 

 

 

 

 

These are just a few examples of how we are able to meet the demands of a wide variety of extraordinary processes. Whether you are looking to move “common” materials like plastic pellets or maybe something “off the wall”, chances are we have the resources to provide an engineered solution to fit your need. Our application engineers are standing by, so give us a call and let us put our expertise to work for you!

Justin Nicholl
Application Engineer
justinnicholl@exair.com
@EXAIR_JN