Intelligent Compressed Air: Sliding-Vane Compressors

If you’re an active reader of the EXAIR blog, you’ve seen several posts over the last year about the various different types of air compressors. From the positive-displacement style of compressors (Rotary Scroll, Rotary Screw, Single and Double Acting Reciprocating Compressors,) as well as a review of a dynamic style (Centrifugal Compressors). In this blog, I’ll be discussing another of the positive-displacement variety: The Sliding-Vane Compressor.

Sliding Vane2
Air enters from the right, and as the compression chamber volume reduces due to counterclockwise rotation, the pressure increases until the air discharges to the left

In positive-displacement type compressors, a given quantity of air or gas is trapped in a compression chamber. The volume of this air is then mechanically reduced, causing an increase in pressure. A sliding-vane compressor will consist of a circular stator that is housed in a cylindrical rotor. The rotor then has radially positioned slots where the vanes reside. While the rotor turns on its axis, the vanes will slide out and contact the bore of the stator wall. This creates compression in these “cells”. An inlet port is positioned to allow the air flow into each cell, allowing the cells to reach their maximum volume before reaching the discharge port. After passing by the inlet port, the size of the cell is reduced as rotation continues and each vane is then pushed back into its original slot in the rotor.  Compression will continue until the cell reaches the discharge port. The most common form of sliding-vane compressor is the lubricant injected variety. In these compressors, a lubricant is injected into the compression chamber to act as a lubricant between the vanes and the stator wall, remove the heat of compression, as well as to provide a seal. Lubricant injected sliding-vane compressors are generally sold in the range of 10-200 HP, with capacities ranging from 40-800 acfm.

Advantages of a lubricant injected sliding-vane compressor include:

  • Compact size
  • Relatively low purchase cost
  • Vibration-free operation does not require special foundations
  • Routine maintenance includes lubricant and filter changes

Some of the disadvantages that come with this type of compressor:

  • Less efficient than the rotary screw type
  • Lubricant carryover into the delivered air will require proper maintenance of an oil-removal filtration system
  • Will require periodic lubricant changes

With the host of different options in compressor types available on the market, EXAIR recommends talking to a reputable air compressor dealer in your area to help determine the most suitable setup based on your requirements. Once your system is up and running, be sure to contact an EXAIR Application Engineer to make sure you’re using that compressed air efficiently and intelligently!

Tyler Daniel

Application Engineer

E-mail: TylerDaniel@exair.com

Twitter: @EXAIR_TD

Diagram:  used from Compressed Air Challenge Handbook

About Sliding Vane Air Compressors

Over the last few months, my EXAIR colleagues have blogged about several different types of air compressor types including single and double acting reciprocating and rotary screw. (You can select the links above to check those out.) Today I will review the basics of the sliding vane type, specifically the oil/lubricant injected sliding vane compressor.

The lubricant injected sliding vane compressor falls under the positive displacement-type, the same as the other types previously discussed.  A positive displacement type operates under the premise that a given quantity of air is taken in, trapped in a compression chamber and the physical space of the chamber is mechanically reduced.  When a given amount of air occupies a smaller volume, the pressure of the air increases.

Each of the previous positive displacement type compressors use a different mechanism for the reduction in size of the compression chamber.  The single and double acting reciprocating use a piston that cycles up and down to reduce the compression chamber size. The rotary screw uses two inter-meshing rotors, where the compression chamber volume reduces as the air approaches the discharge end.  For the lubricant sliding vane type, the basic design is shown below.

Sliding Vane2
Air enters from the right, and as the compression chamber volume reduces due to counterclockwise rotation, the pressure increases until the air discharges to the left

The compressor consist of an external housing or stator, and the internal circular rotor, which is eccentrically offset.  The rotor has radially positioned (and occasionally offset) slots in which vanes reside.  As the rotor rotates, the centrifugal forces on the vanes cause them to move outwards and contact the inner surface of the stator bore.  This creates the compression areas, formed by the vanes, rotor surface and the stator bore.  Because the rotor is eccentrically offset, the volume of the compression area reduces as the distance between the rotor surface and the stator reduces.  As the rotor turns counterclockwise, the vanes are pushed back into the rotor slots, all the while in contact with the stator surface.  The shrinking of the compression area leads to the increase in air pressure.

Oil is injected into compression chamber to act as a lubricant, to assist is sealing, and to help to remove some of the heat of compression.

The advantages of the lubricant sliding vane compressor type is very similar to the lubricant injected rotary screw.  A few key advantages include:

  • Compact size
  • Relatively low initial cost
  • Vibration free operation- no special foundation needed
  • Routine maintenance includes basic lubricant and filter changes

A few of the disadvantages include:

  • Lubricant gets into the compressed air stream, requires an air/lubricant separation system
  • Requires periodic lubricant change and disposal
  • Less efficient than rotary screw type
  • Not as flexible as rotary screw in terms of capacity control in meeting changing demands

EXAIR recommends consulting with a reputable air compressor dealer in your area, to fully review all of the parameters associated with the selection and installation of a compressed air system.

If you would like to talk about compressed air or any of the EXAIR Intelligent Compressed Air® Products, feel free to contact EXAIR and myself or one of our Application Engineers can help you determine the best solution.

Brian Bergmann
Application Engineer

Send me an email
Find us on the Web 
Like us on Facebook
Twitter: @EXAIR_BB

 

Diagram:  used from Compressed Air Challenge Handbook