A Cold Gun Increase Speed for a Reel Manufacturer

When it comes to die stamping, friction generates heat.  Heat can be a big cause in slowing production and decreasing tool life.

Reel Film

A reel manufacturer was seeing the effects of the heat in their process.  They had a stamping machine that was creating sprocket holes in the outer edge of a 35mm film.  These holes are used for advancing the reel strip through printers, projectors, and processing machines.  They had to be particularly careful, as film materials warp easily with heat.  Some of us remember the film reels that would bubble and burn out when the film stopped in the projector.  (I am giving away my age a bit).  So, speed was critical as they did not want to create any quality issues.

They were intrigued with the EXAIR Vortex Tubes as it can generate cold air by only using compressed air.  Vortex Tubes do not use refrigerants or have any moving parts.  They are very compact and can fit into tight places.  If they could reduce the temperature in the stamping process, then they could speed up production.

Compact Vortex Tube

With the Vortex Tubes, EXAIR adds accessories to help with installations for different applications.  For this customer, the Cold Gun Aircoolant System was the best product to deliver the cold air.  I recommended the model 5315 Cold Gun System.  This product generates 1000 BTU/hr of cooling power, and it has a Dual Point Hose Kit to target both sides of the film reel.  It includes a magnetic base to securely position it on the stamping machine, and two 1” flat nozzle ends to attach at the end of the Dual Point Hose Kit.  These flat nozzles would help to direct the cold air in between the two stamping plates.   They were able to keep the film reel and the die stamp cool as they sped up their operation.  Even with the additional speed, they also noticed that the die stayed sharper 20% longer before they had to rework.

Cold Gun with Dual Hose Point

If you believe that heat is slowing down your system, EXAIR may have a product to keep it cool.  With the customer above, heat was a “reel” problem.  With the Cold Gun System, we were able to increase their productivity and decrease their downtime.  You can contact an Application Engineer to discuss your application if you believe that temperature is affecting your process.


John Ball
Application Engineer

Email: johnball@exair.com
Twitter: @EXAIR_jb


Photo: Movie Reel Film Cinema by JanBaby.  Creative Commons CC0 Public Domain.

Solving Static Problems with EXAIR Ion Bars

This plastic film stretching machine needed a viable static elimination solution.

The relationship between humidity and static is something we’re very familiar with at EXAIR.  As temperatures drop and humidity decreases, the reduction in moisture content within the air translates to an increase in static .  This is because higher moisture content in the air creates a surface layer of moisture that dissipates accumulated static charges.  When this surface layer disappears, static forms quickly and easily.

Fortunately, we have a full line of static eliminating equipment suitable for use in removing static related process disturbances.  For example, the photo above shows a plastic stretch wrapping machine at its dispensing point.  As the plastic is pulled from the roll static builds up quickly and this customer needed an easy, reliable solution to remove the static.  Ideally, they wanted something that would not require compressed air, but could still mount closely to the machine and remove the static charge.

The solution for this application was a series of two 24” Ion Bars mounted on each side of the film.  As the plastic is unrolled it passes through the opening created by the Ion Bars, eliminating the static charge.  The machine required no significant downtime to install this solution, and nothing within the machine setup had to be modified.

This type of setup was ideal because it treated the static at the proper point within the process, used no compressed air (as requested by the customer), and it provided a simple installation to solve the problem.

Plastic sheets and films that are being separated after full contact can generate significant static charge.  If you have a film/sheet application, or another static related need, contact an EXAIR Application Engineer.  We’d love to help you find a solution.

Lee Evans
Application Engineer

EXAIR Super Air Knife vs. Blower-type Air Knife

Super Air Knife Blower Air Knife
Super Air Knife                           Blower Air Knife

A plastic company was developing thin layered films in their laboratory on a miniature prototype machine. It was designed for trial runs to make 24” wide material from various plastics, blends, and thicknesses.  They would place the plastic pellets into a hopper, and the material would be melted and extruded into a flat sheet.  To harden the material, it would land onto a cold drum, a large cylinder that had chilled water running through it.  To keep the sheet on the surface of the cold drum, they had a blower air knife.  In addition to the blower air knife, they had to use two ¼” copper air lines blowing on the outside section of the film.  Whenever they decided to make a change to their process, change material runs, or even for clean up; they had to move the blower air knife from the cold drum.  This was a hassle as it had a 3” hose attached to a blower.  It was very cumbersome and awkward to handle.  They heard about the EXAIR Super Air Knives, and they wanted me to do a comparison to their current system.  I was glad to compare the EXAIR 110224 Super Air Knife to their blower-type air knife system.


  1. They were getting “stretch” marks on the plastic film.
    • Blower-type air knife – Hot air is generated by the blower system. When the hot air hits the cool surface, it will cause an uneven hardening of the material, causing stretch marks.
    • Super Air Knife – It has a 40:1 amplification ratio. That means that 40 parts of the ambient air is entrained with 1 part of compressed air. Being that the ambient air is much cooler than the hot air from the blower system, it actually aides in cooling. There is no thermal shock to the material, and hardening is better and faster.
  2. They required an even force across the surface of the plastic film to keep against the cold drum.
    • Blower-type air knife – Their design had one 4” line feeding into the side of the blower air knife. This would cause 2 issues for an even force. As the velocity of the air hits the opposite side of the knife, the closed end, a turbulent air flow is developed. Also, there would be a slight negative pressures at the entrance caused by the velocity of the air entering. This turbulent mayhem and slight negative pressure are very inconsistent in force and velocity. The reason that they had to add the additional two ¼” copper lines to blow compressed air on the outside edges.
    • Super Air Knife – The flow that is delivered from the Super Air Knife is laminar. This means that the force and velocity is consistent across the entire length, even on the outside. With this even force, the film is held evenly and securely onto the cold drum.
  3. They needed maneuverability for change overs and clean up.
    • Blower-type air knife – To keep the needed pressure on the film, they had to have the blower air knife ¼” from the surface of the cold drum. So, before a change over or clean up procedure is started, they had to remove the knife and attachments. This was time consuming, cumbersome, and a headache to move.
    • Super Air Knife – With the compact design, the Super Air Knife has a large force in a small package. It has a footprint of 1 ¾” X 1 ½” X 24” long with only two ¼” NPT compressed air lines feeding it. The force measurement is equivalent from 3” to 12” away from the surface. Now, they could mount the Super Air Knife far enough to not disrupt their cleaning or change-over procedures. This saved them much time in changing to different materials and clean up.
  4. They wondered about the compressed air usage.
    • Blower-type air knife – This device does not require any compressed air to operate, but because it could not keep the film against the cold drum on the outer edges, they did have to use compressed air. With the two ¼” copper tubing at 80 psig, they were using a total of 79 SCFM of compressed air.
    • Super Air Knife – As a direct comparison to their air usage, the Super Air Knife would use 70 SCFM of compressed air at 80 psig across the entire width of the film. But with the unique design to entrain 40 parts of ambient air, it gives the Super Air Knife a powerful force. They were able to reduce the air pressure to 40 PSIG to keep the film on the cold roll, which also cut the air consumption to 41 SCFM. This efficient design helped them to save on compressed air without the added cost of the electricity to run the blower motor.
  5. Any other comparisons between the two products
    • Blower-type air knife – With the sound of the blower and the turbulent air flow, the unit was very loud. It had a sound level over 90 dBA, and with the operators working around this system, they required PPE for hearing.
    • Super Air Knife – These units are very quiet. At 40 PSIG, the sound level is only 61 dBA. (Just as a reference, the sound level is 72 dBA at 100 PSIG). This was very nice for the operators as they did not need to wear the ear plugs to work around their machine all day.

When it comes to using the EXAIR Super Air Knife, it has many benefits over the blower-type air knife. We can even include the initial cost in which we would be about 1/10 the cost of a blower-type air knife system.  For this customer above, they were delighted to replace that system with the Super Air Knife, and start running plastic film effectively, efficiently, and quietly on their miniature prototype machine.

John Ball
Application Engineer
Email: johnball@exair.com
Twitter: @EXAIR_jb