E-Vac for Epoxy Recycling

Recently, a manufacturer of custom magnetics called in about a special application. In the manufacturing of certain electronic systems, a very expensive, thick epoxy glue is used. They were exploring ways to be able to collect the excess after application.  They had used a system in the past and were looking to replicate it.  The previous system had an old boxy vacuum generator, and they asked us if we could provide a vacuum source that matched the performance specifications but in a more compact design.  After researching the specifications and a comprehensive comparison, we could offer the EXAIR model 810013 Inline E-Vac, generating up to 27 ” Hg of vacuum.  A basic sketch of the design concept is shown below-

Capture

By using the model 810013 to create a vacuum within the chamber, a strong suction can be generated at the tube inlet, strong enough to draw in the excess epoxy. The glue can be collected in the chamber for recycling and reuse, and because of the design, the glue does not pass through the E-Vac and cause any issues with build up or blockage that would hinder the performance, leading to the need to clean the unit.

In-LineE-VacFamily

The Many Sizes of E-Vac Models Available

EXAIR manufactures E-Vac’s for both porous and non-porous applications, as well as a line of Adjustable E-Vac Generators.  Smallest units use only 1.5 SCFM of 80 PSIG compressed air and the largest Adjustable E-Vac unit can pull 81 SCFM of air at open draw and 15″ Hg vacuum level setting.  With a wide range of sizes and types, there is a model available to meet your vacuum generation needs.

As a side note – the EXAIR Reversible Drum Vac, High Lift Reversible Drum Vac, Chip Trapper, and High Lift Chip Trapper all use this same basic principle of applying a vacuum to a chamber, but on a much larger scale, to turn a 5, 30, 55 or 110 gallon drum into an industrial liquid vacuum system.  The vacuum generating unit is of a different design, made specifically for the Industrial Housekeeping Products.

To discuss your process and how an EXAIR Intelligent Compressed Air Product can solve your toughest application issues, feel free to contact EXAIR and myself or one of our other Application Engineers can help you determine the best solution.

Brian Bergmann
Application Engineer

Send me an email
Find us on the Web
Like us on Facebook
Twitter: @EXAIR_BB

 

Solving Static Problems with an Ion Point

ipcutout_559x

An Ion Point can provide static elimination with a small footprint and easy installation

I came into the office today to find an interesting application in my inbox.  A small plastic parts manufacturer was facing a problem when sealing their items inside of plastic bags.  The problem arose from an inability to properly place a small strip of glue on the bags, resulting in unwanted glue on the parts and, at times, the exterior of the bags.  What should have been a small strip of glue ended up as a random spread of adhesive due to a static charge on the plastic bags. So, they contacted EXAIR for a static solution.

In this application the first important parameter to check was the type of glue in use.  Some glues are flammable and the vapors from them can be potentially ignitable, so making sure there was no risk for explosion was our first priority as our products are not recommended for use in potentially flammable or combustible applications.

After determining there was no risk for explosion, we then considered the application in more detail.  The static solution needed to be small, effective, and there was an important aspect for this application – the solution could not have any airflow.  The parts which are placed into these bags have low weights, and even a small airflow could remove them from the bags.  So, we needed an airless solution that was compact and effective.

The solution was an Ion Point.

An Ion Point creates a small ionizing “zone” of approximately 2” x 2” (51mm x 51mm) without any airflow.  At this distance, the static elimination from an Ion Point can dissipate a 5kV charge in 0.24 seconds.  The small footprint and airless operation of the Ion Point made it an ideal candidate for this application.

By installing an Ion Point between the bag opener and the glue applicator, the static charge was eliminated and the process disturbance was removed.  We were able to solve this problem, offering a readily available solution (from stock) that fit the specifics of the application.

As the temperature and humidity in the northern hemisphere drop, static problems become more prevalent.  (Click here or here to read about why this happens.)  If static problems arise in your facilities, consider an EXAIR solution.  We’re available to discuss applications and solutions M-F, 8-5 EST.

 

Lee Evans
Application Engineer
LeeEvans@EXAIR.com
@EXAIR_LE

%d bloggers like this: