Compressed Air Accessories for Clean Air, Quiet Air, and Adjustability

In this blog, I would like to turn your attention to our accessories that support our Intelligent Compressed Air® Products.  EXAIR products use compressed air to coat, conserve, cool, convey and clean.  To maximize the performance, it is important to have the controls and options to increase their “flexibility”.  EXAIR offers these items as Accessories.  Pneumatic applications come in many variations and forms, and Accessories can help you to adapt to your application and to remove any “guess work”.

Here are the different categories and explanations of each item that EXAIR recommends for our products.  With their defined functions, they can help you in different areas to enhance your pneumatic experience.

Filters/Regulators:

  • Filter Separators remove bulk liquid and contamination from the compressed air stream. EXAIR stocks a range of sizes from ¼” NPT ports to 1 ¼” NPT ports.  They use a 5-micron filter and a mechanical baffle to remove slugs of liquid from your compressed air system.  Most Filter Separators have an auto-drain to automatically remove the buildup of liquid inside the bowl.   I would consider the Filter Separator as a minimum level of protection required to protect your EXAIR products.
  • The Oil Removal Filters remove very small particles of dirt and oil from the compressed air; making it even cleaner. The 0.03-micron media of the Oil Removal Filter will “coalesce” the fine liquid particles into large droplets.  Thus, allowing gravity to remove it from the compressed air stream.  EXAIR offers different sizes ranging from ¼” NPT to 1 ½” NPT ports.  As a note, Oil Removal Filters are great for removing very fine particles, but if you have a system with lots of water, I would recommend a Filter Separator upstream of the Oil Removal Filter for optimal filtration.
  • Pressure Regulators control the amount of air pressure being supplied to your EXAIR products. This is important if you are trying to save compressed air, control the force, or convey material.  EXAIR, being a leader in compressed air savings, recommends to use the minimum amount of air pressure to do the job.  This will save compressed air and save you money.  Regulators have a characteristic called “droop”.  Droop is the amount of air pressure that it drops downstream when you start flowing compressed air.  If the regulator is not sized properly, you can “starve” your pneumatic component, causing loss of function.  EXAIR properly sizes our regulators in our kits to make sure that you won’t “starve” our product.
  • EXAIR also offers Mounting Brackets for the regulators and the filters to help support them to a wall or structure. To connect filters and regulators together without a pipe nipple, we also have Coupling Kits for sizes up to ¾” NPT.  And for combination kits which includes a filter and a regulator, we offer the Mounting Bracket and Coupling Kit together for a set.

Silencing Mufflers:

  • Reclassifying Mufflers are designed to have two functions. They can reduce noise levels by 35 dB and remove oil mist from the exhaust air.  Cylinders and valves that exhaust pressurized air may have oil in the line to keep the seals from sticking.  When exhausted, it can create a fine mist which is dangerous for operators.  The Reclassifying Mufflers can reduce the loud noise as well as collect any contamination from the exhaust air.
  • Sintered Bronze Mufflers are simple in design, cost effective, and easy to install. They have a minimal back pressure to not restrict operations of the pneumatic device.  They come in sizes from #10-32 thread to 1-1/2 NPT.  For a quick and simple way to reduce noise, the Sintered Bronze Mufflers are in stock for fast delivery.
  • Straight-Through Mufflers offer a way to reduce noise levels without worrying about clogging. They have an aluminum shell lined with sound absorbing foam, and they can reduce the noise level by 20 dB.  EXAIR offers them with two ports from ¼” NPT to ¾” NPT.  This can allow you to connect other items like blowing hose kits while reducing noise.
  • Heavy Duty Mufflers have an outer aluminum shell with an internal stainless steel screen that can protect the components from environmental contamination, and can also keep contaminant like rust from being ejected at high speed into the work area. They have a typical noise reduction of 14 dB.

Pneumatic Valves:

  • Manual Valves allow for operators to turn on and off their system by hand. The full-flow ball valves range from ¼” NPT to 1 1/4” NPT in size and will not restrict flow.  EXAIR also offers a manual foot pedal valve for hands-free operations.  This ¼” NPT Foot Valve has a 3-way operation and works great if the operator has to use both hands in their process.
  • Solenoid Valves are a way to turn on and off the supply of compressed air electrically for automated systems. We offer solenoids in three different voltages; 110Vac, 240Vac, and 24Vdc.  EXAIR has a large range of flows with ports ranging from ¼” NPT to 1” NPT.  All models are UL listed and are CE and RoHS compliant.

Hardware:

  • Swivel Fittings are a great way to securely install and aim EXAIR nozzles. They are dynamic as they can be adjusted and set to a flow direction with 50-degrees of movement.  They are made from 303SS or 316SS for corrosion resistance with ports ranging from 4mm to 1” NPT.
  • Compressed Air Fittings are a nice arrangement to connect different compressed air items together. We offer a range of hex and close nipples, couplings, reducers, tees, elbows, crosses and bulk head fittings.  If you need a quick way to connect directly to your pneumatic system, we may have it on the shelf.
  • Magnetic Bases are designed for a solid mount to steel surfaces and for easy portability of your blow-off system to different locations. It has a 100 lb. (45.5Kg) pulling force to keep the blowing device attached firmly until you want to move it.  They can be mounted in a vertical or horizontal position.  EXAIR offers a single outlet Magnetic Base (for one blow-off device); a dual outlet Magnetic Base (for multiple blowing products); and a single outlet Swivel Magnetic Base (to offer more flexibility to orientation).  The bases come with a ¼ turn shut-off valve to easily turn on and off the compressed air to the EXAIR products.
  • Receiver Tanks are used to store compressed air. They can be used at the air compressor or as secondary reservoirs for intermittent demand.  They help your compressed air system with pressure variations and high demand loads.  EXAIR offers a model 9500-60 Receiver Tank that has a capacity of 60 gallons, is rated to 200 psig, and meets ASME pressure vessel code.

 

Hoses:

  • Conveying Hoses are used with our Air Operated Conveyors or Line Vacs. The hoses are made from a durable PVC semi-flexible hose with six different diameters from ¾” I.D. up to 3” I.D.  The conveyance hoses can slip easily to the ends of the Line Vacs or to tubes for an easy transition.  EXAIR can cut-to-length Conveying Hoses up to 50 feet (15m); in increments of 10 feet (3m).
  • Coiled Hoses get compressed air from the piping system to the EXAIR product. They are made of a durable abrasion-resistant nylon material that is 12 feet long (3.6 meters).  They have swivel fittings at the end to allow for easy uncoiling, and a spring strain relief to keep the hose from kinking.  The coiled design makes it easy to reach around the work area and retract back to the substation.  This will help to keep the hose off the ground where potential dangers could occur.  We offer 3 different connection sizes; 1/8” NPT, ¼” NPT, and 3/8” NPT.
  • Compressed Air Hoses is another way to supply EXAIR products. They are useful if you need to reach from overhead sources or around equipment.   They are made from a reinforced synthetic rubber in 3/8” I.D. and 1/2” I.D. diameters.  We can make specific lengths up to 50 feet (15m).  They are rated for 250 PSIG (17 bar) air pressure, and the hose material works well for long-lasting protection against ozone, weathering and temperatures up to 158oF (70oC).  They come standard with two male ends in ¼” NPT or ½” NPT.

    Flexible and durable, EXAIR Stay Set Hoses come in lengths from 6″ to 36″.
  • Stay Set Hoses give you that possibility of manually adjusting or re-adjusting Super Air Nozzles. The hose has a “memory” function; so, it will not creep or droop until you physically move it.  They work well to direct air flows in unique ways at specific target areas.  They can be used with Super Air Nozzles, Safety Air Guns and Blow-off Kits.  The Stay Set Hoses come in lengths from 6” (15cm) to 36” (91cm), and they are offered with ¼” NPT male on both ends or with a 1/8” NPT female and a ¼” NPT male connections.  These hoses are rated for 250 PSIG (17 bar) and are made from reinforced synthetic rubber.

Temperature Accessories:

  • The ETC, or Electronic Temperature Control, is a digital temperature controller with a LED screen for precision monitoring and adjusting temperatures in a Cabinet Cooler System. The controller has easy-to-use buttons to raise or lower the desired internal cabinet temperature.  Once set, the ETC will hold the temperature to +/- 1 oF (+/- 0.5 oC).  The LED displays the internal temperature for continuous monitoring.  The ETC comes complete with the controller and a solenoid valve in two different voltages, 120Vac and 240Vac.
  • The thermostat is a way to control a solenoid valve electrically to turn on/off a Cabinet Cooler System at a set temperature. It is preset at 95°F (35°C), but it can be adjusted to other desired temperatures.  It has an accuracy to hold the set temperature within +/- 2 °F (1 °C).  It can handle voltages from 24V to 240V, AC (50/60 Hz) or DC.  They are UL Recognized and CSA certified.

In todays fast-paced world, there is a need to get your devices operating as quickly as possible.  With EXAIR Accessories, they can help you to do that.  Not only will you have confidence, as you are using the items from the manufacturer, but it will minimize downtime, setup, and malfunctions that can occur if using other types of accessories.  If you would like to discuss the proper options with your EXAIR products, an Application Engineer will be happy to help you.

John Ball
Application Engineer
Email: johnball@exair.com
Twitter: @EXAIR_jb

EXAIR Products: Silencing Mufflers Overview

OSHA Standard 29 CFR 1910.95(a), relating to permissible noise exposure levels, states that when employees are subjected to sounds in excess of 90 dBA, some type of control should be used to reduce the sound level. In an industrial setting, it’s very common to find the exhausting air from air operated devices such as actuators, diaphragm pumps or cylinders for example, to produce sound levels well above the allowable limits set forth in the Standard. EXAIR offers a variety of different Silencing Mufflers that help to reduce this  noise level, while also increasing operator safety.

 

Reclassifying Mufflers are available in 1/8″, 1/4″, 3/8″, 1/2″, 3/4″ and 1″ NPT sizes

EXAIR’s Reclassifying Mufflers offer noise reduction up to 35 dB and are available in sizes ranging from 1/8″ to 1″ NPT. These types of mufflers are often considered”dual-purpose” as they not only reduce the noise level but also remove oil from the exhaust airflow by incorporating a removable filter element.  The exhausting oil mist is reduced from 50 PPM (parts per million) to only 0.015 PPM, when the device is operated at 100 PSIG. In addition, there is a bowl on the bottom to capture any residual oil and a 1/4″ tube adaptor to allow for easy draining.

Sintered Bronze Mufflers are available in #10-32, 1/8″, 1/4″, 3/8″, 1/2″, 3/4″, 1″, 1-1/4″ and 1-1/2″ NPT sizes, as well as 1/2-20 UNF female for use with solenoid valves
Straight Through Mufflers are available in 1/4″, 3/8″ and 3/4″ MNPT x FNPT

Sintered Bronze Mufflers are a relatively low cost option, commonly used with air cylinders as they can be installed quick and easy. We offer 1o different sizes, ranging from #10-32 for small installations, up to 1-1/2″ NPT for larger scale applications. The noise reduction depends on the size of the muffler and back pressure, which can occur from dirt or particulate clogging the muffler, restricting the exhausting airflow from passing through the porous sintered bronze.

Our Straight Through Mufflers are made of corrosion resistant aluminum and are lined with a sound absorbing foam, capable of reducing noise levels up to 20 dB. We offer 3 different sizes, 1/4″, 3/8″ and 3/4″ NPT, with a male thread on one end and female thread on the other. We incorporate this muffler design into our Cold Guns and Adjustable Spot Coolers and they are commonly used with our Vortex Tubes, Cabinet Cooler® Systems and E-Vac® Vacuum Generators as well.

Heavy Duty Mufflers are available in 1/4″ and 3/8″ FNPT

Lastly, the Heavy Duty Mufflers feature an internal, 50 mesh stainless steel screen, to protect against contaminants in the airflow,  and a corrosion resistant aluminum outer shell. In most cases, the sound reduction can be as high as 14 dB and we offer 2 different sizes, 1/4″ and 3/8″ FNPT. These types of mufflers are regularly used on the hot air exhaust of our Vortex Tubes.

For help with product selection or to discuss a particular process, please contact one of our application engineers at 800-903-9247.

Justin Nicholl
Application Engineer
justinnicholl@exair.com
@EXAIR_JN

Vacuum Generator System Selection – EXAIR E-Vacs

E-Vac Vacuum Generators are a highly efficient, versatile compressed air vacuum pump. Their versatility allows them to be adapted to many applications such as pick and place, clamping or vacuum forming. They’ve also been used in more unique applications like wood veneer pressing and basketball deflation.

EXAIR manufactures (3) types of E-Vacs – Low vacuum generators for porous materials, like cardboard, generating up to 21″ Hg with vacuum flows as high as 18.5 SCFM. Our high vacuum generators, designed for use with non-porous materials like glass or steel sheets, produce vacuum levels up to 27″ Hg and up to 15.8 SCFM of vacuum flow. The adjustable generators provide flexible vacuum performance, up to 25″ Hg and 81 SCFM,  which can be easily adapted to meet the application.

EXAIR E-Vacs provide instantaneous vacuum response, and are engineered for high efficiency to minimize air consumption.

 

When making a selection, there are a few key areas you want to consider:

Is the material porous or non-porous?

  • This will allow you to select the proper type of vacuum generator to fit the application and the type of vacuum cup best suited for the process.

 

What is the weight of the part and how will it be lifted?

  • If the part is being lifted where the vacuum cups will be positioned horizontally, like on top of a sheet of glass, you want to use a safety factor of 2 times the actual weight of the part. In processes requiring the cups be positioned vertically on the part, such as picking up a sheet of plywood and hanging it on an overhead conveyor, a safety factor of 4 would be used.

 

How many Vacuum Cups do I need?

  • Consider the quantity and placement to evenly distribute the weight for safely moving the material.
  • Depending on the maximum vacuum the generator produce, how much weight can each cup lift?
  • Make the cup selection per the following chart

 

Once you have selected the type and number of cups needed, you can then begin to look at which additional accessories items you might need.

  • Filters – supplying clean, dry air is key for maintaining optimal performance. An automatic drain filter  can be used to remove any water or contaminants in the supply line. If there is oil present, consider using an Oil Removal Filter.
  • Mufflers – help to reduce the noise level without restricting the airflow. We offer 2 different styles – Standard and Straight Through. Standards mufflers are a good choice where the supply air is clean and dry. These mufflers can only be used with the porous and non-porous generators. The Straight Through mufflers reduces sound levels by up to 26 dBA and are the better choice in processes where dirt or particulate may be present.
  • Tubing and Fittings – polyurethane tubing is available in 10′ sections up to 50′ for processes requiring the vacuum cups be placed in a location that wouldn’t allow for direct mounting to the NPT vacuum port on the generator or where multiple cups are needed. You want to keep the length of tubing as short as possible though for effective pickup and release time.
  • Check Valve – will maintain vacuum on the load if the supply pressure were to drop or be lost during operation.

For additional assistance selecting the proper E-Vac and accessories for your process, please contact an application engineer at 800-903-9247.

Justin Nicholl
Application Engineer
justinnicholl@exair.com
@EXAIR_JN

 

EXAIR Accessories – We’ve Got you Covered

When you work with us here at EXAIR, we strive to have all the ancillary items that you might need to make your installation a success, without having to find components at the last minute or perhaps using the wrong sized components. Each specific product line such as Super Air Knives or Line Vac air operated conveyors have specific accessories such as mounting brackets or plumbing kits which EXAIR has made to simplify the installation of those particular products. We also carry generalized accessories which work across all of the product lines so you do not have to use multiple vendors or purchase orders.

Silencing Mufflers – Per OSHA Standard 1910.95(a), a worker must not be exposed to sounds levels above 90 dBA for any eight hour shift of a 40 hour work week.  EXAIR offers several types of mufflers including – Reclassifying, Sintered Bronze, Straight-Through and Heavy Duty.  For reducing the noise associated with an EXAIR E-Vac Generator, Vortex Tube, Cabinet Cooler System, or the exhaust air from cylinders, valves and other air powered equipment, we’ve got a muffler that will help to keep the noise level at an acceptable level.

Mufflers

Solenoid and Manual Valves – The easiest way to reduce compressed air usage and save on operating expense is to turn off the compressed air to a device when it isn’t needed. EXAIR carries a wide assortment of solenoid valves, with offerings in the NEMA 4/4X classification, and supply voltages of 24VDC, 120VAC, and 240VAC.  We also have manual ball valves from 1/4 NPT to 1-1/4 NPT and a foot operated valve, with 1/4 NPT connections.

Valves

Swivel Fittings, Stay Set Hoses and Magnetic Bases – To provide a great degree of flexibility for positioning an EXAIR Super Air Nozzle, Air Jets or Air Amplifiers, EXAIR offers several items.  The Swivel Fittings have 25 degree of movement from the center axis, providing a total of 50 degree of adjustability.  The position is locked in place and holds until adjustment is needed. For applications where frequent re-positioning of the air device is required, the Stay Set Hoses are ideal.  Simply mount the hose close to the application, bend it to the shape preferred, and because the hose has “memory”, it will not creep or bend.  Lastly, the Magnetic Bases are another option for flexible, movable installations.  The base has a on/off valve, and a powerful magnet to hold in any vertical or horizontal mounting arrangement.

Swivels, StaySets,MagBases2

 

Hoses – EXAIR can provide hoses for your application.  For the Line Vac air operated conveyor applications, we offer conveyance hose – a durable, clear reinforced PVC hose, in diameters of 3/8″ to 3″ ID, and lengths up to 50′. On the compressed air side, we can provide 12′ Coiled Hoses with 1/8, 1/4, and 3/8 NPT connections, and also 3/8″ and 1/2″ ID hose in lengths to 50′.

Hoses

Filter Separators, Oil Removal Filters and Pressure Regulators – Perhaps the most important accessories for use on a compressed air device are filters and regulators. Filtering the compressed air of dirt, debris, moisture and oil will help to prevent build up inside the EXAIR products, leading to longer service life, and less time spent cleaning, while providing optimum performance. Regulating the air pressure allows for tuning of the performance, using the proper amount of compressed air to obtain satisfactory results.

Filter and Regualtors

If you have questions regarding accessories for use with any EXAIR Intelligent Compressed Air® Product, feel free to contact EXAIR and myself or one of our Application Engineers can help you determine the best solution.

Brian Bergmann
Application Engineer

Send me an email
Find us on the Web 
Like us on Facebook
Twitter: @EXAIR_BB