Accessories, Don’t Forget About Accessories!

Accessories

I went to the auto parts store to replace my brakes on my vehicle.  They asked me if I needed some Anti-squeak grease for my brake hardware.  It made me think about the accessories that EXAIR sells.  I could have used my own kind of grease which may not be able to hold up to the heat, but for a few dollars more, I wanted to go with the item that the experts would suggest.

In this blog, I would like to turn your attention to the accessories that support our Intelligent Compressed Air® Products.  EXAIR products use compressed air to coat, conserve, cool, convey and clean.  To maximize the performance and/or ease installation it is important to have the controls and options, and EXAIR offers these items as Accessories.

Pneumatic applications come in many variations and forms, and Accessories can help you to adapt to your application and to remove “guess work”.  They can make installation easier, add flexibility, and give you peace of mind.

Here are the different categories and explanations for each item that EXAIR recommends for our products with their defined functions.  They can help you in different areas to enhance your EXAIR product experience.

Automatic Drain Filter Separator (left,) and a Pressure Regulator (right.) Oil Removal Filters (optional; center) are also available if needed.

Filters/Regulators:

  • Filter Separators remove bulk liquid and contamination from the compressed air stream. EXAIR stocks a range of sizes from ¼” NPT ports to 1 ¼” NPT ports.  They use a 5-micron filter and a mechanical baffle to remove slugs of liquid from your compressed air system.  Most Filter Separators have an auto-drain to automatically remove the buildup of liquid inside the bowl.   I would consider the Filter Separator as a minimum level of protection required to protect your EXAIR product installations.
  • Oil Removal Filters remove very small particles of dirt and oil from the compressed air; making it even cleaner. The 0.03-micron media of the Oil Removal Filter will “coalesce” the fine liquid particles into large droplets.  Thus, allowing gravity to remove oil vapor from the compressed air stream.  EXAIR offers different sizes ranging from ¼” NPT to 1 ½” NPT ports.  As a note, Oil Removal Filters are great for removing very fine particles, but if you have a system with lots of water, I would recommend a Filter Separator upstream of the Oil Removal Filter for optimal filtration.
  • Regulators control the amount of air pressure being supplied to your EXAIR product. This is important if you are trying to save compressed air, control the force produced by an Air Knife, or convey material slowly.  EXAIR, being a leader in compressed air savings, recommends to use the minimum amount of air pressure to do the job.  This will save compressed air and save you money.  Regulators have a characteristic called “droop”.  Droop is the amount of air pressure that it drops downstream when you start flowing compressed air.  If the regulator is not sized properly, you can “starve” your pneumatic components, causing loss of function.  EXAIR properly sizes our regulators in our kits to make sure that you won’t “starve” your application.
  • Mounting Brackets for the regulators and the filters to help support them to a wall or structure are available. To connect filters and regulators together without a pipe nipple, we also have Coupling Kits for sizes up to ¾” NPT.  And for combination kits which includes a filter and a regulator, we offer the Mounting Bracket and Coupling Kit together for a set.

Silencing Mufflers:

  • Reclassifying Mufflers are designed to have two functions. They can cut noise levels by 35 dB and remove oil mist from the exhaust air.  Cylinders and valves that exhaust pressurized air may have oil in the line to keep the seals from sticking.  When exhausted, it can create a fine mist which is dangerous for operators.  The Reclassifying Mufflers can reduce the loud noise as well as collect any contamination from the exhaust air.
  • Sintered Bronze Mufflers are simple in design, cost effective, and easy to install. They have a minimal back pressure to not restrict operations of the pneumatic device.  They come in sizes from #10-32 thread to 1-1/2 NPT.  For a quick and simple way to reduce noise, the Sintered Bronze Mufflers are in stock for fast delivery.
  • Straight-Through Mufflers offer a way to reduce noise levels without worrying about clogging. They have an aluminum shell lined with sound absorbing foam, and they can reduce the noise level by 20 dB.  EXAIR offers them with two ports from ¼” NPT to ¾” NPT.  This can allow you to connect other items like blowing hose kits while reducing noise.
  • Heavy Duty Mufflers have an outer aluminum shell with an internal stainless steel screen that can protect the components from environmental contamination, and can also keep contaminant like rust from being ejected at high speed into the work area. They have a typical noise reduction of 14 dB.

Pneumatic Valves:

  • Manual Valves allow for operators to turn on and off their system by hand. The full-flow ball valves range from ¼” NPT to 1 1/4” NPT in size and will not restrict flow.  EXAIR also offers a manual foot pedal valve for hands-free operations.  This ¼” NPT foot valve has a 3-way operation and works great if the operator has to use both hands in their process.
  • Solenoid Valves are a way to turn on and off the supply of compressed air electrically for automated systems. We offer solenoids in three different voltages; 110Vac, 240Vac, and 24Vdc.  EXAIR has a large range of flows with ports ranging from ¼” NPT to 1” NPT.  All models are UL listed and are CE and RoHS compliant.

Hardware:

EXAIR’s Swivel Fitting Family
  • Swivel Fittings are a great way to securely install and aim EXAIR nozzles. They are dynamic as they can be adjusted and set to a flow direction with 50-degrees of movement.  They are made from 303SS or 316SS for corrosion resistance with ports ranging from 4mm to 1” NPT.
  • Compressed Air Fittings are a nice arrangement to connect different compressed air items together. We offer a range of hex and close nipples, couplings, reducers, tees, elbows, crosses and bulk head fittings.  If you need a quick way to connect directly to your pneumatic system, we may have it on the shelf.

    Model 9043
  • Magnetic Bases are designed for a solid mount to steel surfaces and for easy portability of your blow-off system to different locations. It has a 100 lb. (45.5Kg) pulling force to keep the blowing device attached firmly until you want to move it.  They can be mounted in a vertical or horizontal position.  EXAIR offers a single outlet Magnetic Base (for one blow-off device); a dual outlet Magnetic Base (for multiple blowing products); and a single outlet Swivel Magnetic Base (to offer more flexibility to orientation).  The bases come with a ¼ turn shut-off valve to easily turn on and off the compressed air to the EXAIR products.
  • Receiver Tanks are used to store compressed air. They can be used at the air compressor or as secondary reservoirs for intermittent demand.  They help your compressed air system with pressure variations and high demand loads.  EXAIR offers a model 9500-60 Receiver Tank that has a 60 gallon capacity and is rated to 200 PSIG.  It meets the ASME pressure vessel code.

    Universal Air Mounting Kit
  • Universal Air Knife Mounting System gives you a way to mount the EXAIR Super Air Knife, Full-Flow Air Knife, and Standard Air Knife. This kit is used to position your air knife securely and precisely.  It comes with a bracket and an articulated arm that can reach up to 30” (762mm).  You can orientate the air knives in any position to maximize the effectiveness.

    Plumbing Kits
  • Plumbing Kit, or PKI, is a great tool for longer Super Air Knives to help attach your compressed air system. They are designed to help lessen the time for install as well as to properly supply compressed air equally along the entire length, specifically for 24” (610mm) and longer.  We can offer the Plumbing Kit separately if you find that it could benefit your fabricators during installation.
  • Coupling Kits are designed to attach Aluminum and Stainless Steel Super Air Knives if you need to extend past the 108” (2,743 mm) width. Coupling Kits will mount the air knives together end to end.

Hoses:

  • Conveying Hoses are used with our Air Operated Conveyors or Line Vacs. The hoses are made from a durable PVC semi-flexible hose with six different diameters from ¾” I.D. up to 3” I.D.  The conveyance hoses can slip easily to the ends of the Line Vacs or to tubes for an easy transition.  EXAIR can cut-to-length Conveying Hoses up to 50 feet (15m); in increments of 10 feet (3m).
  • Coiled Hoses get compressed air from the piping system to the EXAIR product. They are made of a durable abrasion-resistant nylon material that is 12 feet long (3.6 meters).  They have swivel fittings at the end to allow for easy uncoiling, and a spring strain relief to keep the hose from kinking.  The coiled design makes it easy to reach around the work area and retract back to the substation.  This will help to keep the hose off the ground where potential dangers could occur.  We offer 3 different connection sizes; 1/8” NPT, ¼” NPT, and 3/8” NPT.
  • Compressed Air Hoses is another way to supply EXAIR products. They are useful if you need to reach from overhead sources or around equipment.   They are made from a reinforced synthetic rubber in 3/8” I.D. and 1/2” I.D. diameters.  We can make specific lengths up to 50 feet (15m).  They are rated for 250 PSIG (17 bar) air pressure, and the hose material works well for long-lasting protection against ozone, weathering and temperatures up to 158oF (70oC).  They come standard with two male ends in ¼” NPT or ½” NPT.
  • Stay Set Hoses give you that possibility of manually adjusting or re-adjusting Super Air Nozzles. The hose has a “memory” function; so, it will not creep or droop until you physically move it.  They work well to direct air flows in unique ways at specific target areas.  They can be used with Super Air Nozzles, Safety Air Guns and Blow-off Kits.  The Stay Set Hoses come in lengths from 6” (15cm) to 36” (91cm), and they are offered with ¼” NPT male on both ends or with a 1/8” NPT female and a ¼” NPT male connections.  These hoses are rated for 250 PSIG (17 bar) and are made from reinforced synthetic rubber.

Temperature Accessories:

  • The ETC, or Electronic Temperature Control, is a digital temperature controller with a LED screen for precision monitoring and adjusting temperatures in a Cabinet Cooler System. The controller has easy-to-use buttons to raise or lower the desired internal cabinet temperature.  Once set, the ETC will hold the temperature to +/- 1 oF (+/- 0.5 oC).  The LED displays the internal temperature for continuous monitoring.  The ETC comes complete with the controller and a solenoid valve in two different voltages, 120Vac and 240Vac.
  • The thermostat is a way to control a solenoid valve electrically to turn on/off a Cabinet Cooler System at a set temperature. It is preset at 95°F (35°C), but it can be adjusted to other desired temperatures.  It has an accuracy to hold the set temperature within +/- 2 °F (1 °C).  It can handle voltages from 24V to 240V, AC (50/60 Hz) or DC.  They are UL Recognized and CSA certified.

In today’s fast-paced world, there is a need to get your devices operating correctly and as quickly as possible.  EXAIR Accessories can do that.  Not only will you have confidence, as you are using the items recommended by the EXAIR experts, but you won’t have to worry about your system “squeaking” to a halt.  Like with my brakes above; I was happy to use the recommended grease to end any annoyance with my braking.  If you would like to discuss the proper options with your EXAIR products, an Application Engineer will be happy to help you.

John Ball
Application Engineer
Email: johnball@exair.com
Twitter: @EXAIR_jb

Super Air Knife Plumbing Kits Ensure Proper and Optimum Operation

The EXAIR Super Air Knife is a Highly Engineered and intelligently designed point of use compressed air powered device that delivers a 40:1 air amplification ratio!  This simply means that for every one part compressed air supplied to an EXAIR Super Air Knife it will entrain 40 parts ambient air into the exiting compressed air stream.  Almost as good as “money for nothing”!  Also the EXAIR Super Air Knife is designed to provide an even or “laminar” flow of air.  This is due to it being an intelligent, highly engineered compressed air product.

However if an EXAIR Super Air Knife is not connected to the compressed air supply with the appropriate number of inlet ports being fed, poor and/or erratic performance is likely.  This would manifest itself as uneven air flow and lower performance from the air knife.  In order to make this plumbing easier we offer optional plumbing kits for all Super Air Knives starting with the 24″ length all the way up to the 108″!  The 24″ and longer Super Air Knive’s require that compressed air must be supplied to multiple air inlets along its length for optimal performance.  This will ensure that the air flow is laminar and the force is even across the entire length of the Super Air Knife.  All our products are shipped with an installation guide referencing the proper recommended pipe sizes for various lengths of supply pipe.

The Plumbing Kits for Aluminum Super Air Knives provide properly sized Nitrile/PVC Hoses, Brass Fittings and a Pressure Gauge which monitors the inlet pressure to the air knife.  If the gauge shows a pressure drop when the Super Air Knife is turned on this indicates that there is an air starvation issue.  For the 303SS, 316SS and PVDF Air Knives the Plumbing Kits contain 5/8 OD SS tubing X .034 wall thickness tubing and SS fittings.

AirKnifePlumbing

So when ordering your next Super Air Knife be sure to designate the Plumbing Kit to ease your installation and to ensure top performance.

When you are looking for expert advice on safe, quiet and efficient point of use compressed air products give us a call.   We would enjoy hearing from you!

Steve Harrison
Application Engineer
Send me an email
Find us on the Web 
Follow me on Twitter
Like us on Facebook

Super Air Knife is Most Efficent in Compressed Air Usage

 Of the 3 styles of Air Knife offered by EXAIR, the Super, Standard and Full-Flow, the Super Air Knife is our most efficient, in regards to compressed air usage. Using a 40:1 amplification rate of entrained ambient air to compressed air consumed, it uses only 2.9 SCFM per inch of knife length when operated at 80 PSIG, while producing a low sound level of only 69 decibels (the quietest on the market today). The Super Air Knife provides  an even laminar flow of air across the length of the knife and is available in single piece lengths from 3″ up to 108″ in aluminum, 303 stainless and 316 stainless as well as up  to 54″ in PVDF (Polyvinylidene Flouride) construction for applications where aggressive chemicals may be present. 1/4″ FNPT air inlets are available on each end as well as on the bottom of the knife.

Aluminum, Stainless Steel and PVDF Super Air Knives

For Super Air Knives 24″ and longer, you need to plumb air to multiple inlets to maintain an even airflow. Our available Plumbing Kits includes the properly sized hose or pipe and fittings, to not only save valuable time looking for these parts yourself but also eliminates the potential of using undersized lines which will reduce the performance of the Super Air Knives.

For Super Air Knives in aluminum construction, the Plumbing Kits include cut to length PVC compressed air hose and the required brass fittings.

Plumbing Kit for aluminum Super Air Knives

The Plumbing Kits for our stainless steel and PVDF Super Air Knives, include 316ss cut to length pipe as well as 316ss fittings.

Plumbing Kit for 303ss, 316ss and PVDF Super Air Knives

The Super Air Knife is the ideal choice when looking to treat wide-area applications, like cleaning a conveyor or drying parts after a wash process. For help selecting the best product to fit your process, contact one of our application engineers for assistance.

Justin Nicholl
Application Engineer
justinnicholl@exair.com
@EXAIR_JN

 

An Overview of EXAIR’s Award Winning Super Air Knife

 

Loud and inefficient homemade blowoff

Drilled pipes, like the one shown above, are all too common in industrial settings for processes where a wide surface area needs to be treated. Their popularity can be attributed to how cheap and easy they are to make but in actuality they are very expensive to operate, as they waste large amounts of compressed air, and are very dangerous to operate.

We frequently take calls from customers looking for a more energy efficient, safer solution to replace these types of blowoffs. EXAIR manufactures 3 different styles of Air Knife – the Super, Standard and Full-Flow – that are the ideal solution for wide coverage applications. Today, I would like to provide an overview of our award wining Super Air Knife.

The Super Air Knife

The Super Air Knife is our most efficient air knife in regards to compressed air usage, using only 2.9 SCFM per inch of knife length @ 80 PSIG. It is also the quietest on the market today at only 69 decibels. The Super Air Knife provides the highest air velocity of the 3 styles offered by EXAIR and produces 2.5 ounces of force per inch at 80 PSIG operating pressure. We offer stock lengths from 3” up to 108” in single piece construction with available materials of aluminum, 303ss and 316ss. We also offer PVDF (Polyvinylidene Fluoride) up to 54” for harsh environments.

The Super Air Knife provides a laminar airflow across the entire length with hard-hitting force. They also give a 40:1 amplification rate meaning they entrain 40 parts of the surrounding room air for every 1 part of compressed air used, producing a large volume outlet flow.

Coupling Kit for the Super Air Knives

For applications requiring an air knife length longer than 108″, we offer a coupling bracket kit that allows you to connect two Super Air Knives together for a seamless, uninterrupted flow. Kits are available in aluminum, 303ss or 316ss to match the construction of the knife.

In addition, we also offer plumbing kits as an accessory item. For aluminum Super Air Knives, we offer cut to length nitrile/PVC hose and brass fittings and for stainless steel and PVDF knives we offer 316ss cut-t0-length pipe and fittings.

If you have any questions on how the Super Air Knife might fit into your process, please contact an Application Engineer.

Justin Nicholl
Application Engineer
justinnicholl@exair.com
@EXAIR_JN

Super Air Knife Plumbing Kit Allows Installation In Tight Quarters

I recently had the pleasure of helping a long-time user of our Super Air Knives with a challenging application. They already use quite a few of our Model 110012SS 12″ Stainless Steel Super Air Knives to clean & dry their nonwoven material as it’s being rolled for packaging. They like them because they’re quiet and efficient, but also because they’re durable…this particular product off-gasses a mildly corrosive vapor, which used to corrode other equipment in the area. Not only does the Stainless Steel Super Air Knife resist corrosion itself, the air flow keeps these vapors contained. Two birds, one stone.

They have a new product…same kind of material, but much wider…that needed to be blown off, and the identified the Model 110060SS 60″ Stainless Steel Super Air Knife as a “no-brainer” solution. Thing is, it had to be a pretty even air flow across the length, and a 60″ Super Air Knife has to get air to four ports across its length for optimal performance. And, they wanted to install it at a point where it would serve not only as a blow off, but as a vapor barrier, just like the 12″ Super Air Knives they’re already so fond of. The space was a little limited, though, so they opted for the Model 110060SSPKI 60″ Stainless Steel Super Air Knife with Plumbing Kit Installed, which allowed them to simply run an air supply line to both ends.

EXAIR SS Super Air Knives can be ordered with a Plumbing Kit installed, or you can easily install a Plumbing Kit on your existing Super Air Knife.

If you want to find out more about an engineered solution for your compressed air application – cleaning, drying, vapor barrier, or all of the above – give me a call.

Russ Bowman
Application Engineer
Find us on the Web
Follow me on Twitter
Like us on Facebook

Plumbing Kits Simplify Air Knife Installation

Incorrect plumbing is an all too common problem we deal with on a regular basis here at EXAIR. Many times we receive calls from a customer saying that their Air Knife isn’t producing a high velocity or they are seeing an uneven airflow. In fact we have written many blogs touching on this subject, such as the one I posted a few weeks ago titled, Proper Air Supply & Installation Provides Best Performance or the one titled Typical Compressed Air Plumbing Mistakes by our International Application Engineer John Ball.

Using undersized supply lines can cause excessive pressure drops because they aren’t able to carry the volume of air necessary to properly supply the compressed air device. We commonly reference trying to supply water to a fire hose with a garden hose, it is the same principle. Using restrictive fittings, like quick disconnects, will also contribute to this effect as the ID of the fitting is much smaller than the NPT connection size. Example: Say you are seeing 80-100 PSIG upstream of  an air knife at the pressure gauge, by the time the air passes through a quick disconnect or small ID line and fitting, the actual pressure being delivered to the unit will be much less, possibly as low as 20-30 PSIG depending on the installation. One way to measure the actual pressure being delivered to the air knife would be to install a pipe tee with a pressure gauge right at the inlet of the air knife.

All of our products are shipped with an installation guide referencing the proper recommended pipe sizes for various lengths of supply pipe. When dealing with our Air Knives, since we offer lengths up to 108″, you need to plumb air to multiple inlets for knives that are 24″ and larger. To simplify the installation process, we offer our Air Knife Plumbing Kits. The Plumbing Kits include properly sized nitrile/PVC compressed air hose and brass fittings for our aluminum units. In addition, we now offer 316ss pipe and fittings for our stainless steel and PVDF Super Air Knives for applications requiring superior corrosion resistance. Using the plumbing kits eliminates pressure loss and the need for searching for the proper fittings or possibly using incorrect pipe size.

Aluminum Plumbing Kit
Plumbing Kit for aluminum Super Air Knife

 

SS Plumbing Kit
Plumbing Kit for Stainless Steel and PVDF Super Air Knife

 

If you think you are experiencing less than expected performance from one of our products, please give us a call so we can help.

Justin Nicholl
Application Engineer
justinnicholl@exair.com
@EXAIR_JN

 

.