Intelligent Compressed Air: Save $$ With a Leak Prevention Program

Don’t let leaks drive up your utility bill

The generation of compressed air accounts for approximately 1/3 of all energy costs in an industrial facility. According to the Compressed Air Challenge, about 30% of that compressed air is lost through leaks. This means nearly 10% of your facility’s energy costs are simply wasted through poor connections, faulty air valves, improper installation, etc. In addition to simply wasting money, compressed air leaks can also contribute to a variety of other operating losses. A leak can cause a drop in system pressure. When this occurs, end users may not operate as efficiently, having an adverse effect on production. This same drop in system pressure will also cause the equipment to cycle on/off more often, shortening the life of your compressor and other equipment. If the leaks cause an issue in supply volume, it may lead to the belief that more compressor capacity is necessary, further increasing your operating costs.

To put leaks in perspective (assuming energy costs of .10/ kWh), the Compressed Air Challenge states this:

  • A $200/year leak cannot be felt or heard
  • A $800/year leak can be felt, but not heard
  • A $1,400/year leak can be felt and heard.

If you walk through your facility, how many leaks can you hear?

We know that a large portion of the compressed air is being wasted, but what do we do about it? A proper leak prevention plan is the key to success. Since these leaks are impossible to see and some cannot even be heard, you need a tool to help assist you. EXAIR’s model 9061 Ultrasonic Leak Detector is the right tool for the job. When compressed air leaks through a pipe, it creates an ultrasonic signature due to turbulence. While this sound is not always detectable by the human ear, this meter will allow you to locate leaks up to 20’ away.


Model 9061 with parabola attachment

The first step will be locating the leaks using an Ultrasonic Leak Detector and tagging them throughout the facility. Don’t let this overwhelm you!! If you have a larger facility, break it up into sections that can be completed in 1 day. This will allow you to decide which areas of the plant should be looked at first. Once you’ve located and tagged all of the leaks, rate them under two separate criteria so that you can prioritize what to fix first. Rate them based on the difficulty that it will take to fix them and also by the severity of the leak. Those that are severe yet easy to fix would make sense to begin fixing first. Those that may require a period of shutdown can be planned to fix at a more appropriate time.

Accessories that come with the Ultrasonic Leak Detector

When you’ve had the opportunity to fix them, don’t just forget about it. When new piping is installed, new lines are added, or anything involving compressed air is installed there is the potential for new leaks to develop. Set this as one of your regular PM activities and complete your own compressed air audit once a year. Implementing the process and maintaining it are the keys to your success.

If you have questions about developing a leak program or how to use the Ultrasonic Leak Detector, give us a call. An Application Engineer will be happy to help with the process and recommend additional methods to save on your compressed air supply.

Tyler Daniel
Application Engineer
Twitter: @EXAIR_TD

EXAIR’s Adjustable Spot Cooler: A Versatile Tool for Your Cooling Needs!


If you’re looking at replacing messy coolant mist systems, look no further than the Adjustable Spot Cooler. EXAIR’s Adjustable Spot Cooler incorporates Vortex Tube technology to produce temperatures ranging from -30°F – +70°F. A Vortex Tube works by imparting a rapid spinning motion to the supplied compressed air. This airflow makes its way to the end of the tube where it is forced to abruptly change directions. It is during this change of direction that energy is given off in the form of heat. The hot air then exits the tube from the hot end, while cold air exits the other end of the tube. As the valve is opened to allow more air to exhaust from the hot end, the temperature at the cold end will decrease. At a sound level of just 73 dBA when operated at 100 psig and stock generator installed, this compact cooler will keep your operation cool, clean and dry without causing unnecessarily high noise levels.

Critical tolerances are maintained on plastic parts using the Adjustable Spot Cooler


When looking at a Vortex Tube based solution, the variety of options can sometimes be daunting. This is where the versatility of the Adjustable Spot Cooler shines. Through a simple turn of the control knob, you can easily adjust the temperature and cold fraction of the unit. Additionally, the kits come with (2) extra generators (15-H and 30-H) that can be swapped out for the stock generator for more/less cooling power and air consumption. The 15-H generator will deliver up to 1,000 Btu/hr of cooling capacity and the 30-H will provide up to 2,000 Btu/hr of cooling capacity. We have (2) different kits available, the Model 3825 Single Point and the Model 3925 Dual Point Kit. The 3825 is recommended for use in applications where you’re cooling a small surface such as solder joints, hot melts, or drilled plastics. The 3925 system is better served when heat is generated over a larger surface area such as saw blade cooling. The kits use flexible Loc-Line hose to allow you to precisely position the cold airflow onto your target. The Adjustable Spot Cooler provides easy mounting with a swivel magnetic base, allowing you to mount the cooler directly at the most critical point that heat is being generated.

3825_3925 adj spot cooler

If you’re tired of cleaning up your coolant or have an application that requires dry machining, get one of the Adjustable Spot Cooler systems on order today. They’re in stock ready to ship!

Tyler Daniel
Application Engineer
Twitter: @EXAIR_TD