In most “general” blowoff applications, the conical airflow pattern from a standard round shaped nozzle is ideal when trying to remove dust or light debris from the surface of a part or material. However in certain applications, a focused, laminar flow of air is required to produce the desired result, such as cleaning peanut butter from a fill nozzle or ejecting parts in a stamping operation.
EXAIR manufactures our 1″ Flat and 2″ Flat Super Air Nozzles, which provide a 1″ and 2″ (respectively) wide, forceful stream of high velocity, laminar airflow while consuming only a small amount of compressed air. Both the 1″ and the 2″ are available in Zinc Aluminum alloy, rated up to 250°F (121°C), or 316 Stainless Steel construction, rated up to 1,000°F (538°C)
Their unique design incorporates a specially designed, replaceable shim, to maintain a critical gap between the cap and body, resulting in the focused airflow. They are shipped from stock with a .015″ shim installed.
Using the optional shim kit, the shims can be changed out to .005”, .010” or .020”, which allow you to increase or decrease the force and flow by either opening or closing the gap, providing more or less force and flow to meet the demand of the application.
(Here’s a short video showing how easy it is to change out the shims)
We also offer our High Power versions of these nozzles which feature a thicker shim installed (0.025″) for applications requiring higher thrust and velocity.
If you have an application you would like to discuss or to see how the Flat Super Air Nozzles might improve your process, give me a call, I’d be happy to help.
A cardboard manufacturing facility was using a 3/8” outside diameter (OD) open tube to blow scrap cardboard off a conveyor. This scrap cardboard would occasionally be blown inside the roller area at the end of a conveyor creating a maintenance nightmare that required hours to disassemble and remove. To prevent this from occurring they installed another 3/8″ OD open compressed air tube to divert any cardboard headed toward the conveyor roller. The 3/8″ open tubing eliminated the scrap problem, but introduced a few new ones. The open hose is extremely noisy over (100 dBA). It does not comply with OSHA standard CFR 1910.242(b), which requires that a compressed air blow off device may not be dead ended at more than 30 PSIG. The most costly problem though is a 3/8″ open tubing uses a tremendous amount of compressed air.
They were using so much air in the facility that they were draining the system pressure in their facility. Obviously, they were going to replace the open tube with EXAIR 2” Flat Super Air Nozzle. Replacing this open blow off with an intelligent compressed air product, like the HP1125 High Powered Flat Super Air Nozzle or the 1104 Super Air Nozzle, would lower the noise level below 83 dBA. Also, those nozzles use significantly less air. They decided to use the model HP1125 for its thin profile to fit into the tight location. The only question was how much air and energy cost would they save. They could have easily installed a Digital Flow Meter on the supply pipe of the open tube to measure the change in flow once the EXAIR nozzle had been installed, but they wanted to try and estimate the air usage.
Using EXAIR’s test data, we know a 3/8″ OD open tube that is 18″ long will flow 68.5 SCFM at 80 PSIG. An HP1125 2″ Flat Super Air Nozzle utilizes 37 SCFM when fed with 80 PSIG inlet pressure. By removing one 3/8″ OD tube the cardboard manufacturer saved 31.5 SCFM of compressed air. With an electrical cost of $0.08 per kWh, compressed air costs $0.25 per 1000 SCF. Saving 31.5 SCFM reduces the manufacturers electrical bill by $0.48 every hour, $3.48 for every 8 hour shift, and $960 per year (250 working days, eight hours a day). If the manufacturer runs two shifts, the savings will double. The simple return on investment for this nozzle is 130 hours! How many projects can you measure a return on investment in hours?
Take advantage of our free service – the EXAIR Efficiency Lab. Our Application Engineers will test any nozzle or device you choose to send in to the Lab using our calibrated testing equipment. We’ll compare the performance of your existing product (air consumption, noise, force, etc.) with an EXAIR Intelligent Compressed Air product. The results will be published in a comprehensive report, including a cost savings analysis with simple ROI. For most applications, EXAIR products can help you improve compressed air efficiency AND pay for themselves in a matter of weeks!
EXAIR intelligent compressed air products are easy to install, safe, and efficient. By installing these products instead of using unsafe open blow offs, your company can save thousands of dollar every year with minimal investment. While saving electrical expenses, we decrease the noise level which makes your production force a nicer place to work. We also comply with OSHA’s standards. Finally, we may be able to design the blow off better to consistently produce the quality product you expect. Call EXAIR today to discuss your application.