Tag: best practice

Dryers On A New Level – Deliquescent Level Even.

Published on by Brian FarnoLeave a comment

Today I want to discuss dryers and not the type that I have repaired many times due to having three kids in my house. Speaking of which, the amount of hair that gets trapped within a dryer is one of the things my nightmares are made from. You’d think we have a Yeti living in our home. While the picture below is of our first dryer and washer, that platform has been repurposed into a workbench and the metals have all been recycled back into something else now. That’s not what we are here to talk about. Instead, we are going to discuss deliquescent dryers.

Deliquescent dryers can sometimes be confusing. Some compressed air dryer vendors use the terms deliquescent and desiccant synonymously, as if they were interchangeable in describing their equipment. Deliquescent dryers are not complex drying systems and are most commonly found in the petrochemical industry.

Deliquescent Dryer

Unlike any other dryer, a deliquescent dryer is also used to reduce or remove moisture before it turns to liquid water. These dryers can be installed indoors, outdoors, offshore, or in any remote location. They do not require electricity for operational purposes or have any moving parts, making them easy to maintain and economically more efficient. In a deliquescent dryer, moist air (gas) passes over a layer of deliquescent tablets that absorb moisture. The pressure dew point lowers as the tablets slowly dissolve, the condensation falls into the drain area, and the drier air flows through the outlet into the piping system.

The best deliquescent materials are salts due to their strong attraction to moisture. Deliquescent desiccants (drying tablets) are formulated from calcium chloride, magnesium chloride, potassium chloride, and lithium chloride. Not all deliquescent desiccants are equal. The final formulation and properties of the desiccant can significantly impact the design of a dryer tank. That is, the surface of the desiccant chemical, often beads or pellets, will liquefy, and the resulting liquid will flow to the bottom of the vessel. There is either a drain (manual or auto) at the base of the deliquescent dryer which is used to expel the collected fluid.

Some factors that will affect the consumption of the desiccant are the type of adsorbent, type of adsorbate, the size of the adsorbent bead or pellet, the concentration of the adsorbate in the compressed air stream, and the temperature of that air stream.

You will want to have a water trap, also known as a general-purpose compressed air filter, plumbed in line just upstream from the deliquescent dryer. Otherwise, any liquid water flowing with the compressed air into the air dryer will make short work of the desiccant chemical, requiring a more frequent—and expensive—recharge.

Compressing air generates heat. That hot, moist compressed air will consume the desiccant chemical in the deliquescent dryer much more quickly. The best practice is to ensure the airflow to the dryer is as cool as possible, with a long airline and a dwell tank before the deliquescent dryer, to allow the air to cool and have water saturate out naturally.

A deliquescent dryer can be expected to reduce the compressed air dew point by 20 – 30 deg. F, or so. The degree of drying depends how saturated the airflow is going in and on the type of deliquescent chemical used.

Unlike other forms of compressed air dryers, a deliquescent unit doesn’t guarantee the air will reach a certain dew point. The amount of water vapor in the air that exits the dryer is completely predicated on how much water vapor is in the air going into the dryer.

Brian Farno, MBA – CCASS Application Engineer

BrianFarno@EXAIR.com
@EXAIR_BF

Compressed Air Dryers : What are they Good For?

Published on by Jordan T ShouseLeave a comment

Absolutely Nothing….. err ALOT! They are really good for a lot! Specifically removing moisture/condensate from compressed air.

In almost every operation, clean, dry compressed air will result in lower operating costs. The purpose of compressed air dryers is to overcome the dew point of your compressed air by removing water from it. Compressed air can contain humidity, and in the right environments it can reach the dew point temperature and condense into a damaging liquid. This liquid can be problematic, as it can contaminate your products or equipment, causing frozen pipes, and possibly leading to corrosion and other issues.

Now that we know how important they are how do you know which one is right for you?

Types of compressed air Dryers

• Refrigerant Dryer – the most commonly used type, the air is cooled in an air-to-refrigerant heat exchanger. (Here is a great blog deep diving on Refrigerant Dryers)
• Regenerative-Desiccant Type – use a porous desiccant that adsorbs (adsorb means the moisture adheres to the desiccant, the desiccant does not change, and the moisture can then be driven off during a regeneration process). (Here is a great blog deep diving on Desiccant Dryers)
• Deliquescent Type – use a hygroscopic desiccant medium that absorbs (as opposed to adsorbs) moisture. The desiccant is dissolved into the liquid that is drawn out. Desiccant is used up and needs to be replaced periodically. (Here is a great blog deep diving on Deliquescent Dryers)
• Membrane Type– use special membranes that allow the water vapor to pass through faster than the dry air, reducing the amount of water vapor in the air stream. (Here is a great blog deep diving on Membrane Dryers)

The selection of an air dryer is done best by the professional who knows or learns the particular end uses, the amount of moisture which each use can tolerate and the amount of moisture which needs to be removed to achieve this level. Air, which may be considered dry for one application, may not be dry enough for another. Dryness is relative. Even the desert has moisture. There is always some moisture present in a compressed air system regardless of the degree of drying.

For compressed air, the best way to specify dryness is to cite a desired pressure dew point. Different types of dryers, therefore, are available with varying degrees of pressure dew point performance. To specify dew point lower than required for an application is not good engineering practice. (Naming a pressure dew point is how to state the degree of dryness wanted.) It may result in more costly equipment and greater operating expense.

If you have questions about compressed air systems and dryers or any of our 15 different Intelligent Compressed Air® Product lines, feel free to contact EXAIR, and I or any of our Application Engineers can help you determine the best solution.

Jordan Shouse
Application Engineer

Send me an Email
Find us on the Web 
Like us on Facebook
Twitter: @EXAIR_JS

Why Dryers Are Needed in Compressed Air Systems

Published on by Brian FarnoLeave a comment

Air compressors are extremely proficient at compressing anything in the air they are intaking. With that air that is taken in, moisture is going to be present. The amount of moisture will all depend on where you are located geographically and the ambient conditions in the area. Here in Ohio, we experience all 4 seasons so the moisture content is higher in the air during the summer months, rather than the winter months. When this air is saturated with water vapor and the conditions are right, the air reaches a point it cannot hold any additional water vapor. This point is known as the dew point of the air and water vapor will begin to condense to form droplets.

When ambient air is compressed, heat is generated and the air increases in temperature. In most industrial compressed air systems, the air is then processed to an aftercooler, and that is where condensation begins to form. To remove the condensation, the air then goes into a separator which traps the liquid water. The air leaving the aftercooler is typically saturated at the temperature of the discharge, and any additional cooling that occurs as the air is transferred will cause more liquid to condense out of the air. To address this moisture, compressed air dryers are used.

It is critical to the quality of the system and components downstream that actions are taken to prevent this condensation in the air. Condensation is generally detrimental to any point of use application and or the piping that conveys the air. Rust and/or corrosion can occur anywhere in the piping, leading to scale and contamination of the compressed air and processes. When trying to dry products off using compressed air or using the air to atomize a liquid such as paint, adding in these contaminants and moisture will cost production losses.

There are several options when it comes to the type of dryer that one may consider installing on their compressed air supply side.

• Refrigerant Dryer – the most commonly used type, the air is cooled in an air-to-refrigerant heat exchanger.
• Regenerative-Desiccant Type – use a porous desiccant that adsorbs (adsorb means the moisture adheres to the desiccant, the desiccant does not change, and the moisture can then be driven off during a regeneration process).
• Deliquescent Type – use a hygroscopic desiccant medium that absorbs (as opposed to adsorbs) moisture. The desiccant is dissolved into the liquid that is drawn out. Desiccant is used up and needs to be replaced periodically.
• Heat of Compression Type – are regenerative desiccant dryers that use the heat generated during compression to accomplish the desiccant regeneration.
• Membrane Type– use special membranes that allow the water vapor to pass through faster than the dry air, reducing the amount of water vapor in the air stream.
The air should not be dried any more than is needed for the most stringent application, to reduce the costs associated with the drying process. A pressure dew point of 35°F to 38°F (1.7°C to 3.3°C) often is adequate for many industrial applications. Lower dew points result in higher operating costs.
If you have questions about compressed air systems and dryers or any of the 15 different EXAIR Intelligent Compressed Air® Product lines, feel free to contact EXAIR, and I or any of our Application Engineers can help you determine the best solution.

Brian Farno
Application Engineer
BrianFarno@EXAIR.com
@EXAIR_BF

About Air Compressors: Air Intake Best Practices

Published on by Jordan T ShouseLeave a comment

Take a second and think about where the air compressor is located within your facility.  It is more than likely not a major focal point displayed prominently in the floor layout. There is a better chance it is tucked away in a corner of the facility where operators seldom travel.  No matter the type of air compressor, it still has an intake where it pulls in the ambient air from around the compressor then sends it through some process and on the demand side of your compressed air system.  These intakes can easily be placed out of sight and out of mind especially in older facilities that were designed when compressors were loud and the piping layout kept them away from operators due to sound level restrictions.

Air Compressor
Antique Air Compressor (Not safe for use!)

That’s why your compressor manufacturer supplies a specific grade of air inlet/intake filter, and this is your first line of defense. If it’s dirty, your compressor is running harder, and costs you more to operate it.  If it’s damaged, you’re not only letting dirt into your system; you’re letting it foul & damage your compressor. It’s just like changing the air filter on your car, your car needs clean air to run correctly, so does your compressor and the entire demand side of your compressed air system.

According to the Compressed Air Challenge, as a compressor inlet filter becomes dirty, the pressure drop across the inlet increases, this is very similar to the point of use compressed air filters.  The inlet filter on the compressor is the only path the compressor has to pull in the air, when restricted the compressor can begin to starve for air very similar to if you only had a small straw to breath through and told to run a marathon.  A clogged inlet filter can give false symptoms to compressor technicians as well.

The effects can mimic inlet valve modulation which result in increased compression ratios. If we were to form an example based on a compressor with a positive displacement, if the filter pressure drop increases by 20″ H2O, a 5% reduction of the mass flow of air will be present without a reduction in the power being drawn by the compressor. This all leads to inefficiency which easily amounts to more than the cost to replace the depleted inlet air filter.

compressor
Compressed Air System

Where you place the filter is just as important as how often you replace it.  There are some tips to be used when mounting the inlet filter.

  1. The filter can be placed on the compressor, but the inlet pipe should be coming from an external area to the compressor room or even the building if possible. The inlet should be free from any contaminants as well.  Some examples that are easy to overlook are nearby condensate discharges, other system exhausts and precipitation.
  2. Depending on the type of compressor being used, a lower intake air temperature can increase the mass flow of air due to the air density.  A compressor that is lubricant injected is not susceptible to this due to the air mixing with the warmer lubricant before being compressed.

If you would like to discuss improving your compressed air efficiency or any of EXAIR’s engineered solutions, I would enjoy hearing from you…give me a call.

Jordan Shouse
Application Engineer
Send me an email
Find us on the Web 
Like us on Facebook
Twitter: @EXAIR_JS

 

Images Courtesy of  the Compressed Air Challenge and thomasjackson1345 Creative Commons.