Tag: kinetic energy

Air Compressors: Centrifugal Type.

Published on by johnball2014Leave a comment

There are two main ways to compress air for supplying pneumatic systems; Positive Displacement and Dynamic.  Positive Replacement reduces the volume of air within a confined space to generate pressure.  The dynamic type raises the air pressure by using kinetic energy and velocity with rotating impellers that continuously brings in airflow.  In this blog, I will cover the centrifugal type of the dynamic branch. 

As mentioned, the centrifugal compressor works by transforming kinetic energy and velocity into pressure.  Ambient air passes through guide vanes into the center of a rotating Impeller with radial blades and is then pushed outward by a centrifugal force. This radial velocity of air results in an increase in pressure due to kinetic energy.  Let’s look at the equation for kinetic energy in Equation 1:

Equation 1: 

K = ½ * m * V2  

K – Kinetic Energy (J)

m – mass (Kg)

V – velocity (m/s)

As you can see, the energy increases with the square of the velocity.  How do we increase the velocity?  Let’s look at Equation 2:

Equation 2:

V = w * r

V – linear velocity (m/s)

w – angular velocity (rad/sec)

r – radius (m)

As you can see, as the air travels along the impeller towards the outside, the radius increases.  Since the rotations per second are constant, the velocity will increase.  In combination with Equation 1, you can see how the energy will increase, thus increasing the pressure. 

 With the increase in pressure, you will get an increase in heat.  It is a natural occurrence with air compressors.  Heat from the centrifugal compressor is dissipated with heat exchangers before moving onto the next stage.  Multiple stages are required to raise the pressure to a sufficient level for typical industrial plant requirements.  The most common centrifugal air compressors have two to four stages to generate pressures up to 100 to 150 PSIG.  Centrifugal compressors are near the middle of the road regarding efficiency.  Their typical operating cost is 16 to 20 kW/100 CFM. 

Advantages:

  • Up to 1500 HP systems are available
  • Price per Horsepower drops as system size increases
  • Supplies lubricant-free air
  • Special installation pads are not required for installation

Disadvantages:

  • Costs more Initially
  • Requires specialized maintenance

No matter the type of air compressor that you use, they are very costly to operate.  To help you use them efficiently and safely, EXAIR offers a range of products that can clean, cool, blow, conserve, and convey.  This would include our Super Air Knives, Super Air Nozzles, Safety Air Guns, Cabinet Coolers, and much more.  If you want to save energy, increase safety, and cut costs no matter what size air compressor you have; you can contact an Application Engineer at EXAIR.  We will be happy to help you. 

John Ball
Application Engineer
Email: johnball@exair.com
Twitter: @EXAIR_jb

Images Courtesy of the Compressed Air Challenge

Entrainment: What is it?

Published on by johnball2014Leave a comment

By definition, entrainment is a form of the verb, entrain, which is fluid that is swept along into an existing moving flow.   Whenever there is a discussion about fluid dynamics, the Bernoulli’s equation generally comes up.  This equation is unique as it relates flow energy with kinetic energy and potential energy.  The formula was mainly linked to incompressible fluids, but under certain conditions, it can be significant for gas flows as well.  I would like to discuss how EXAIR uses the Bernoulli’s equation for entrainment to maximize efficiency within your compressed air system.

This relationship between pressure as compared to flow and velocity came to be known as the Bernoulli’s principle.  “In fluid dynamics, Bernoulli’s principle states that an increase in the speed of fluid occurs simultaneously with a decrease in static pressure or a decrease in the fluids potential energy”1. Bernoulli realized that the sum of kinetic energy, flow energy, and potential energy is a constant during steady flow.  He wrote the equation like this:

Equation 1:

P/r + V2/2 + gz = constant

P – Pressure

r – density

V – velocity

g – gravitational constant

z – height difference

 

Not to get too technical, but you can see the relationship between the velocity squared and the pressure from the equation above.  Being that this relationship is a constant along the streamline; when the velocity increases; the pressure has to come down.  An example of this is an airplane wing.  When the air velocity increases over the top of the wing, the pressure becomes less.  Thus, lift is created and the airplane flies.

Since we know the criteria to apply the Bernoulli’s equation with compressed air, let’s look at some EXAIR products.  Blowing compressed air to cool, clean, and dry, EXAIR can do it very efficiently as we use the Bernoulli’s principle to entrain the surrounding air.  Remember from the equation above, as the velocity increases, the pressure has to decrease.  When the pressure decreases, the surrounding air will move toward the low pressure.  That low pressure will sweep the ambient air into the air stream; called entrainment.

Compressed air is expensive, but the ambient air is free.  The more ambient air we can entrain, the more efficient the blowing device is.  As an example, we engineer the Super Air Knife to maximize this phenomenon to give an amplification ratio of 40:1. So, for every 1 part of compressed air, the Super Air Knife will bring into the air streamline 40 parts of ambient “free” air.  This makes the Super Air Knife one of the most efficient blowing devices on the market.  By adding mass to the flow stream, it will reduce the compressed air usage, saving you money, and allow for better cooling and a stronger blowing force.  For a drilled pipe, the amplification ratio is generally only two to three times.

We use this principle for many of our products like the Air Amplifiers, Safety Air Guns, Air Nozzles, Air Knives, and Gen4 Static Eliminators. Daniel Bernoulli was able to find a relationship between velocities and pressures, and EXAIR was able to use this to create efficient, safe, and effective compressed air products.  To find out how you can use this advantage to save compressed air in your processes, you can contact an Application Engineer at EXAIR.  We will be happy to help you.

John Ball
Application Engineer
Email: johnball@exair.com
Twitter: @EXAIR_jb

 

  1. Wikipedia https://en.wikipedia.org/wiki/Bernoulli%27s_principle

People of Interest: Daniel Bernoulli

Published on by johnball2014Leave a comment

Daniel Bernoulli

Whenever there is a discussion about fluid dynamics, Bernoulli’s equation generally comes up. This equation is unique as it relates flow energy with kinetic energy and potential energy. The formula was mainly linked to non-compressible fluids, but under certain conditions, it can be significant for gas flows as well. My colleague, Tyler Daniel, wrote a blog about the life of Daniel Bernoulli (you can read it HERE). I would like to discuss how he developed the Bernoulli’s equation and how EXAIR uses it to maximize efficiency within your compressed air system.

In 1723, at the age of 23, Daniel moved to Venice, Italy to learn medicine. But, in his heart, he was devoted to mathematics. He started to do some experiments with fluid mechanics where he would measure water flow out of a tank. In his trials, he noticed that when the height of the water in the tank was higher, the water would flow out faster. This relationship between pressure as compared to flow and velocity came to be known as Bernoulli’s principle. “In fluid dynamics, Bernoulli’s principle states that an increase in the speed of fluid occurs simultaneously with a decrease in static pressure or a decrease in the fluids potential energy”1. Thus, the beginning of Bernoulli’s equation.

Bernoulli realized that the sum of kinetic energy, potential energy, and flow energy is a constant during steady flow. He wrote the equation like this:

Equation 1:

Bernoulli’s Equation

Not to get too technical, but you can see the relationship between the velocity squared and the pressure from the equation above. Being that this relationship is a constant along the streamline; when the velocity increases; the pressure has to come down. An example of this is an airplane wing. When the air velocity increases over the top of the wing, the pressure becomes less. Thus, lift is created and the airplane flies.

With equations, there may be limitations. For Bernoulli’s equation, we have to keep in mind that it was initially developed for liquids. And in fluid dynamics, gas like air is also considered to be a fluid. So, if compressed air is within these guidelines, we can relate to the Bernoulli’s principle.

  1. Steady Flow: Since the values are measured along a streamline, we have to make sure that the flow is steady. Reynold’s number is a value to decide laminar and turbulent flow. Laminar flows give smooth velocity lines to make measurements.
  2. Negligible viscous effects: As fluid moves through tubes and pipes, the walls will have friction or a resistance to flow. The surface finish has to be smooth enough; so that, the viscous effects is very small.
  3. No Shafts or blades: Things like fan blades, pumps, and turbines will add energy to the fluid. This will cause turbulent flows and disruptions along the velocity streamline. In order to measure energy points for Bernoulli’s equation, it has to be distant from the machine.
  4. Compressible Flows: With non-compressible fluids, the density is constant. With compressed air, the density changes with pressure and temperature. But, as long as the velocity is below Mach 0.3, the density difference is relatively low and can be used.
  5. Heat Transfer: The ideal gas law shows that temperature will affect the gas density. Since the temperature is measured in absolute conditions, a significant temperature change in heat or cold will be needed to affect the density.
  6. Flow along a streamline: Things like rotational flows or vortices as seen inside Vortex Tubes create an issue in finding an area of measurement within a particle stream of fluid.

Super Air Knife has 40:1 Amplification Ratio

Since we know the criteria to apply Bernoulli’s equation with compressed air, let’s look at an EXAIR Super Air Knife. Blowing compressed air to cool, clean, and dry, EXAIR can do it very efficiently as we use the Bernoulli’s principle to entrain the surrounding air. Following the guidelines above, the Super Air Knife has laminar flow, no viscous effects, no blades or shafts, velocities below Mach 0.3, and linear flow streams. Remember from the equation above, as the velocity increases, the pressure has to decrease. Since high-velocity air exits the opening of a Super Air Knife, a low-pressure area will be created at the exit. We engineer the Super Air Knife to maximize this phenomenon to give an amplification ratio of 40:1. So, for every 1 part of compressed air, the Super Air Knife will bring into the air streamline 40 parts of ambient “free” air. This makes the Super Air Knife one of the most efficient blowing devices on the market. What does that mean for you? It will save you much money by using less compressed air in your pneumatic application.

We use this same principle for other products like the Air Amplifiers, Air Nozzles, and Gen4 Static Eliminators. Daniel Bernoulli was able to find a relationship between velocities and pressures, and EXAIR was able to utilize this to create efficient, safe, and effective compressed air products. To find out how you can use this advantage to save compressed air in your processes, you can contact an Application Engineer at EXAIR. We will be happy to help you.

John Ball
Application Engineer
Email: johnball@exair.com
Twitter: @EXAIR_jb

  1. Wikipedia https://en.wikipedia.org/wiki/Bernoulli%27s_principle

How a Centrifugal Compressor Works

Published on by Leave a comment

Continuing our series on different types of air compressors, today’s blog will feature the centrifugal compressor.  The centrifugal compressor is classified as a dynamic compressor.  Dynamic compressors are designed to work with  a continuous flow of air that has its velocity increased by an impeller rotating at a very high speed.

The centrifugal compressor works by transforming the kinetic energy and velocity into pressure energy in the diffuser.  The air passes through the inlet guide vanes being drawn into the center of a rotating Impeller with radial blades and is then pushed outward from the center by centrifugal force. This radial movement of air results in a pressure rise and the generation of kinetic energy.  The kinetic energy is also converted into pressure by passing through the diffuser.

Centrifugal Pic 1
Sample Centrifugal Compressor

Multiple stages are required to raise the pressure to a sufficient level for typical industrial plant requirements.  Each stage takes up a part of the overall pressure rise of the compressor unit.  Depending on the pressure required for the application, a number of stages can be arranged in a series to achieve a higher pressure.

The most common centrifugal air compressor has two to four stages to generate pressures of 100 to 150 PSIG and incorporates a water cooled inter-cooler and separator between each stage to remove condensation and cool the air prior to entering the next stage.

Centrifugal compressors are the near middle of the road regarding efficiency, their typical operating cost is 16 to 20 kW/100 CFM.  The most efficient compressor type is the double-acting reciprocating and costs 15 to 16 kW/100 SCFM and the least is the Sliding Vane which costs 21 to 23 kW/100 SCFM.

Advantages of the centrifugal air compressor:

  • Up to 1500 HP systems are available
  • Price per HP drops as system size increases
  • Supplies lubricant-free air
  • Special installation pads are not required for installation

Disadvantages of the centrifugal air compressor

  • Costs more Initially
  • Requires specialized maintenance
  • Due to high rotational speeds (can exceed 50,000 RPM) precision high speed bearings and vibration monitoring are required

EXAIR recommends contacting a reputable air compressor dealer in your area to discuss your volume and pressure requirements to determine the best size & type air compressor for your needs.

Regardless of the type of air compressor you have, EXAIR’s Intelligent Compressed Air Products® can minimize your compressed air consumption, potentially reducing the size of compressor needed, reduce noise and still deliver powerful results!   If you would like to discuss highly efficient and quiet point of use compressed air products or any EXAIR product, we would enjoy hearing from you. 

Steve Harrison
Application Engineer
Send me an email
Find us on the Web 
Follow me on Twitter
Like us on Facebook

 

Image Courtesy of  the Compressed Air Challenge