How to Manage Condensate in Your Compressed Air System

If you operate an air compressor, you’re drawing water vapor into your compressed air system.  Factors like climate control (or lack thereof,) and humidity will dictate how much.  If (or more to the point, when) it condenses, it becomes an issue that must be addressed.  There are several types of dryer systems to choose from, usually when you buy your compressor…we’ve covered those in a number of blogs.  Some of these can leave a little more water vapor than others, but remain popular and effective, when considering the cost, and cost of operation, of the different types.

So, how do you handle the condensate that the dryer doesn’t remove?

  • Receivers, or storage tanks (like EXAIR Model 9500-60, shown to the right,) are commonly used for several reasons:
    • By providing an intermediate storage of compressed air close to the point of use, fluctuations across the system won’t adversely affect an application that needs a constant flow and pressure.
    • This also can keep the air compressor from cycling rapidly, which leads to wear & tear, and additional maintenance headaches.
    • When fitted with a condensate drain (more on those in a minute,) they can serve as a wet receiver.  Condensate collects in the bottom and is manually, or automatically emptied.
  • Condensate drains, while popularly installed on receivers, are oftentimes found throughout larger systems where the vapor is prone to condense (intercoolers, aftercoolers, filters and dryers) and where the condensation can be particularly problematic (drip legs or adjacent to points of use.) There are a couple of options to choose from, each with their own pros & cons:
    • Manual drains are self explanatory: they’re ball valves; cycled periodically by operators.  Pros: cheap & simple.  Cons: easy to blow down too often or for too long, which wastes compressed air.  It’s also just as easy to blow down not often enough, or not long enough, which doesn’t solve the condensate problem.
    • Timer drains are self explanatory too: they cycle when the timer tells them to. Pros: still fairly cheap, and no attention is required.  Cons: they’re going to open periodically (per the timer setting) whether there’s condensate or not.
    • Demand, or “zero loss” drains collect condensate until their reservoir is full, then they discharge the water.  Pros: “zero loss” means just that…they only actuate when condensate is present, and they stop before any compressed air gets out.  Cons: higher purchase price, more moving parts equals potential maintenance concerns.
  • The “last line of defense” (literally) is point-of-use condensate removal.  This is done with products like EXAIR Automatic Drain Filter Separators.  They’re installed close to compressed air operated devices & products, oftentimes just upstream of the pressure regulator and/or flow controls…the particulate filter protects against debris in these devices, and the centrifugal element “spins” any last remaining moisture from the compressed air flow before it gets used.
Good engineering practice calls for point of use filtration and moisture removal, such as that provided by EXAIR Filter Separators.

Efficient and safe use of your compressed air includes maintaining the quality of your compressed air.  If you’d like to find out more about how EXAIR Corporation can help you get the most out of your compressed air system, give me a call.

Russ Bowman
Application Engineer
EXAIR Corporation
Visit us on the Web
Follow me on Twitter
Like us on Facebook

 

Supply Side Review: Deliquescent Type Dryers

As mentioned in my post last week.  The supply side of compressed air systems within a facility is critical to production.  The quality of air produced by your compressor and sent to the demand side of the system needs to be filtered for both moisture and particulate.  One method to dry the air, that is the topic for this blog, is deliquescent type dryers.

These dryers operate like an adsorbent dryer such as a desiccant medium dryer.  The main variance is that the drying medium (desiccant) actually undergoes a phase change from solids to liquids.  Because of this the material is used up and cannot be returned to its original state for reuse.   The liquids formed by the desiccant dissolving in the removed water vapor are then filtered out of the air stream before it is passed on to the demand side of the air system.

There are many compounds that are used to absorb the moisture in the wet compressed air.  A few options are potassium, calcium, or sodium salts and many that contain a urea base.  The desiccant compound must be maintained at a minimum level for the dryer to contain enough media to successfully dry the air.

These dryers are generally a single tank system that is fed with compressed air from a side port near the bottom of the tank.  The air then travels up past drip trays where the desiccant and water mixture fall and ultimately ends up in the bottom of the tank.  The air then goes through a material bed that must be kept at a given level in order to correctly absorb the moisture in the air.  The dry air is then pushed out the top of the tank.

As the desiccant material absorbs the liquid from the compressed air flowing through the tank it falls onto the drip trays and then into the bottom of the tank where it is drained out of the system.  This process can be seen in the image below.

 

Deliquescent type compressed air drying system
How a deliquescent air dryer works – 1(VMAC Air Innovated, 2017)

 

The dew point that this style dryer is able to achieve is dependent on several variables:

  • Compressed air temperature
  • Compressed air pressure / velocity
  • Size and configuration of the tank
  • Compression of the absorption media
  • Type of absorption media and age of media

These dryers are simplistic in their design because there are no moving parts as well as easy to install and carry a low startup cost.

Some disadvantages include:

  • Dewpoint range 20°F – 30°F (Again this is according to the media used.)
  • Dissolved absorption material can pose a disposal issue as it may not be able to be simply put down a drain
  • Replacement of the absorption material

Even with disadvantages the ability to supply the demand side of a compressed air system for a production facility is key to maintaining successful operations.  If you would like to discuss any type of compressed air dryer, please contact us.

Brian Farno
Application Engineer
BrianFarno@EXAIR.com
@EXAIR_BF

 

1 – Deliquescent Dryer Image: VMAC Air Innovated: The Deliquescent Dryer – https://www.vmacair.com/blog/the-deliquescent-dryer/