How to Manage Condensate in Your Compressed Air System

If you operate an air compressor, you’re drawing water vapor into your compressed air system.  Factors like climate control (or lack thereof,) and humidity will dictate how much.  If (or more to the point, when) it condenses, it becomes an issue that must be addressed.  There are several types of dryer systems to choose from, usually when you buy your compressor…we’ve covered those in a number of blogs.  Some of these can leave a little more water vapor than others, but remain popular and effective, when considering the cost, and cost of operation, of the different types.

So, how do you handle the condensate that the dryer doesn’t remove?

  • Receivers, or storage tanks (like EXAIR Model 9500-60, shown to the right,) are commonly used for several reasons:
    • By providing an intermediate storage of compressed air close to the point of use, fluctuations across the system won’t adversely affect an application that needs a constant flow and pressure.
    • This also can keep the air compressor from cycling rapidly, which leads to wear & tear, and additional maintenance headaches.
    • When fitted with a condensate drain (more on those in a minute,) they can serve as a wet receiver.  Condensate collects in the bottom and is manually, or automatically emptied.
  • Condensate drains, while popularly installed on receivers, are oftentimes found throughout larger systems where the vapor is prone to condense (intercoolers, aftercoolers, filters and dryers) and where the condensation can be particularly problematic (drip legs or adjacent to points of use.) There are a couple of options to choose from, each with their own pros & cons:
    • Manual drains are self explanatory: they’re ball valves; cycled periodically by operators.  Pros: cheap & simple.  Cons: easy to blow down too often or for too long, which wastes compressed air.  It’s also just as easy to blow down not often enough, or not long enough, which doesn’t solve the condensate problem.
    • Timer drains are self explanatory too: they cycle when the timer tells them to. Pros: still fairly cheap, and no attention is required.  Cons: they’re going to open periodically (per the timer setting) whether there’s condensate or not.
    • Demand, or “zero loss” drains collect condensate until their reservoir is full, then they discharge the water.  Pros: “zero loss” means just that…they only actuate when condensate is present, and they stop before any compressed air gets out.  Cons: higher purchase price, more moving parts equals potential maintenance concerns.
  • The “last line of defense” (literally) is point-of-use condensate removal.  This is done with products like EXAIR Automatic Drain Filter Separators.  They’re installed close to compressed air operated devices & products, oftentimes just upstream of the pressure regulator and/or flow controls…the particulate filter protects against debris in these devices, and the centrifugal element “spins” any last remaining moisture from the compressed air flow before it gets used.
Good engineering practice calls for point of use filtration and moisture removal, such as that provided by EXAIR Filter Separators.

Efficient and safe use of your compressed air includes maintaining the quality of your compressed air.  If you’d like to find out more about how EXAIR Corporation can help you get the most out of your compressed air system, give me a call.

Russ Bowman
Application Engineer
EXAIR Corporation
Visit us on the Web
Follow me on Twitter
Like us on Facebook

 

Types Of Compressed Air System Dryers

Many times, when discussing product selection with a customer, we commonly reference supplying as clean and dry air as possible to promote peak performance. In iron piping systems for example, when moisture is present, rust can develop which can reduce the performance of end use compressed air operated devices like air tools or cause issues on the exhaust side as you could exhaust unwanted mist onto a surface, like in a painting operation.

Example of a desiccant dryer

Typically, an efficient and properly installed industrial compressed air system will include some type of dryer to remove any moisture that may be present in the supply.

Let’s take a look at the various types of dryers available.

Refrigerant and desiccant dryers are two of the more commonly used types of dryers.

Refrigerant based systems have several stages. The compressed air first passes through an air to air heat exchanger  which initially cools the air. The air is then delivered to an air to refrigerant exchanger where an external source of liquid refrigerant further cools the air and sends it to a separator, where the water vapors condensate and are removed through a drain trap. Now that the air is dry, it is then cycled back to the air to air exchanger where it is heated back to ambient temperature and exits the system.

Desiccant dryers typically incorporate 2 tanks containing a porous desiccant which causes the moisture to sort of “cling” to the surface. In these systems, compressed air flows through one tank, while, using it’s own regeneration cycle, heated or unheated air is blown through the desiccant in the other tank to remove the moisture and dry the air.

Membrane Dryers are typically used at the end use product. These types of systems utilize membranes to dissipate water vapor as it passes through the material, while allowing a small amount of the dry air to travel the length of the membrane to sort of “wipe” the condensate and remove it from the system.

Deliquescent Dryers use a drying agent which absorbs any moisture in the air. As the vapors react with the desiccant, like salt, the desiccant liquefies and is able to be drained at the bottom of a tank. These are the least expensive dryers to purchase and maintain because they have no moving parts and require no power to run.

When a dryer is being considered for a particular setup, there are 3 common reference points used when determining the dryers rating – an inlet air temperature of 100°F, supply pressure of 100 PSIG and an ambient air temperature of 100°F. Changes in supply pressure or temperature could change the performance of a particular dryer. You want to follow the manufacturer’s recommendations when dealing with variances as they will typically provide some type of conversion.

For help with this or any other topics relating to the efficient use of compressed air, please give us a call, we’d be happy to help.

Justin Nicholl
Application Engineer
justinnicholl@exair.com
@EXAIR_JN

 

Heated Desiccant Dryers image courtesy of Compressor1 via creative commons license

Video Blog: Effectiveness of Filtering Your Compressed Air

The video below will give a brief demonstration on the importance of point of use filtration in order to remove unwanted material such as water, scale, particulate and oil from your compressed air stream. Point of use or end-use filtration will keep your air clean and your compressed air products running smooth.  If you have any comments or questions, please feel free to contact us.

 

Brian Farno
Application Engineer
BrianFarno@EXAIR.com
@EXAIR_BF