Tag: ionizers

RoHS, EXAIR, And You

Published on by Russ BowmanLeave a comment

The 20th century was an amazing time for technological advances. In just 70 years, the science & engineering communities went from believing that powered flight was impossible, to actually powering a flight that took three astronauts all the way to the Moon…and back. In the 50 years or so since then, the computers with the power required for space travel went from needing a whole room, to being able to fit on our desks, and eventually, our pockets.

All three of these: a state of the art computer from 1962 (left), the desktop computer I’m writing this blog on (middle), and a smart phone being used for its most popular function (right) all have about the same amount of computing power, believe it or not. (full disclosure: I believe it because I used my smart phone to look that up on the internet)

Along with these amazing advances in technology came exponential increases in the materials it takes to make devices like desktop (or laptop) computers and smart phones…and some of those materials don’t get along well at all with the environment, and by extension, those of us who live in said environment. This doesn’t normally matter as long as those materials are housed inside an operating computer or cell phone (or myriad other electronic devices), but it DOES become a concern when they’re disposed of. When stuff like that ends up in landfills, for instance, it has a bad habit of making its way into the water table…and that’s not good for anyone.

In 2002, the European Union (EU) started pursuing legislation to restrict the use of certain hazardous substances, to get out ahead of disposal issues by keeping them out of products from the very beginning. This led to the creation & implementation of the RoHS Directive. It’s been revised, amended, and updated over the years, because it turns out there are no viable substitutes for SOME of those substances in SOME situations. Among these exceptions:

  • Mercury is used extensively in a number of energy efficient CFL light bulbs and fluorescent tubes, so there are exemptions for that, and it works because there’s a whole industry devoted to the proper recycling of these products.
  • My personal favorite is the specific exclusion for lead in the manufacture of pipe organs. Seems that the lead based alloy that’s been used for centuries is critical to the tonal qualities of the sound that the pipes produce. Since disposal rates of these are negligible (the use of this alloy is one of the reasons they LAST for centuries), pipe organ pipes don’t have to be RoHS compliant.

Compliance with the RoHS Directive is so important to EXAIR, it’s part of our Sustainability Plan. All of our products that are subject to the Directive have certificates of compliance (available upon request) that document their compliance. Per the specifics of the Directive, these are comprised of certain products in our Optimization, Static Eliminators, and Cabinet Cooler System product lines:

  • Optimization:
    • EFC Electronic Flow Control Systems
    • Digital Flowmeters
    • Digital Sound Level Meters
    • Ultrasonic Leak Detectors
  • Static Eliminators:
    • Super Ion Air Knives
    • Standard Ion Air Knives
    • Ionizing Bars
    • Super Ion Air Wipes
    • Ion Air Cannons
    • Ion Air Guns
    • Ion Air Jets
    • Power Supplies
    • Intellistat Ion Air Guns
    • Intellistat Ion Air Nozzles
    • Static Meters
  • Cabinet Cooler System products:
    • Electronic Temperature Control Systems
    • Thermostats & Capacitors
    • Solenoid Valves

These are all of our products that are electrical or electronic in nature. Our broad line of engineered compressed air products are not subject to the Directive, as they have no electrical or electronic components. We DO make sure these comply with other regulatory directives, as applicable, such as:

  • Conflict Mineral Free: All compressed air products
  • CE: All products
  • UL: Static Eliminators and Cabinet Cooler Systems are UL Listed, HazLoc Cabinet Cooler Systems are UL Classified
  • ATEX: These are a brand new line (as of this writing) of Cabinet Cooler products

If you’d like to find out more about EXAIR’s commitment to compliance with any of these standards or directives, give me a call.

Russ Bowman, CCASS

Application Engineer
Visit us on the Web
Follow me on Twitter
Like us on Facebook

Ionizing Points for Static Elimination Without Airflow

Published on by Russ BowmanLeave a comment

I almost wore three socks this morning: one on each foot, and one inside the sleeve of my shirt. I don’t know if it got in there through the agitation & spin of the washing machine, or the tumbling action in the dryer, but I know how it stayed there through the removal from the dryer, folding, and placing in my shirt drawer: static charge. This was evident from the ‘snap, crackle, and pop’ it made when I pulled it out.

Static charge is all around us. It’s mildly annoying in the clothes we pull from the dryer or the packing peanuts we can’t shake from our hands when unpacking from that new whatever-I-just-ordered from that website. It’s surprisingly uncomfortable when we touch the light switch after walking across a carpeted floor. And it’s terrifying when a lightning bolt hits so close that there’s no discernible delay for the thunder.

It’s also prevalent in many industrial processes: molding, trimming, wrapping (or unwrapping), bag & bottle filling, printing…just to name a few. Some materials are more prone to it than others, but all it takes is contact, and separation, of non-conductive surfaces to generate a static charge. The faster and/or more frequent the contact & separation, the higher the charge, and oftentimes there’s no better way to build up static electricity than sliding or rubbing those surfaces together.

EXAIR has a wide variety of Static Eliminator solutions: Super Ion Air Knives for webs or sheets up to 9 feet in width, Ion Air Cannons or Jets for more focused, conical ionized air blowing, Ion Air Guns for handheld operations, Super Ion Air Wipes for tube, pipe, extruded shapes, etc., and Intellistat Ion Air Guns & Nozzles for laboratory or clean room situations. Two of our Static Eliminator Products – Ionizing Bars & Ionizing Points – require no compressed air at all for operation, and one of those is the point (‘pun intended’ or ‘spoiler alert’ – you decide) of today’s blog.

The EXAIR Gen4 Ionizing Point is compact, versatile, and easy to install. It’s perfect for applications where even a light breeze worth of air flow would be disruptive or problematic. It’s also great for ionizing an existing air flow, like in a blower duct or air conveyance line. If limited space is a problem, it’s got the smallest footprint of just about any static eliminator on the market.

The EXAIR Model 8199 Gen4 Ionizing Point packs a LOT of static elimination in a small package.

They have impressive static dissipation performance as well, as seen in the table below. The only maintenance that’s required is a periodic cleaning of the emitter point (with the Power Supply OFF, using a soft bristled, dry brush). Should the emitter point become fouled, it can also be easily replaced.

If you’ve got problems with static charge, EXAIR has a comprehensive offering of solutions…give me a call to find out more.

Russ Bowman, CCASS

Application Engineer
Visit us on the Web
Follow me on Twitter
Like us on Facebook

Gen4 Super Ion Air Wipe Eliminates Static on Bottling Line

Published on by Tyler DanielLeave a comment

Just recently I worked with our Distributor in Argentina on an application for a manufacturer of bottled water. Once the bottles are filled, a protective security seal is placed along the top of the bottle. This serves two purposes, it prevents any form of tampering as well as keeps the cap of the bottle clean throughout the rest of the manufacturing process. Since most people drink directly from the bottle, this area needs to remain clean and not be exposed to contamination later on in the process.

Their problem was that static was building up on this plastic which caused an improper seal on the cap of the bottle. Further down the processing line, the bottles can be exposed to water that contaminates the bottles. They had to implement an inspection process as it was not acceptable to allow any contaminated bottles to leave the plant. Without a solution, they were losing time due to the necessary inspection as bottles were being rejected at a rate of almost 30%.

IMG_2625

The recommended solution was to install a Model 8164 4″ Gen4 Super Ion Air Wipe just prior to the point in the process where the seal was applied. The plastic material passed through the center of the Super Ion Air Wipe which neutralized the static charge on the material. Without a charge, the seal was applied correctly and they were able to eliminate the need of a manual inspection. After installation, the reject rate dropped to 0%!!

The Gen4 Super Ion Air Wipe provides a uniform 360° ionized airstream and is available in both 2” and 4” ID sizes. Its clam-shell design makes it easy to clamp around a part for neutralizing static electricity and contaminants. The high volume, high velocity airflow attaches itself to the surface and wipes it down with static eliminating ions. The airflow stays attached to the surface and is effective up to 15’ away from where it’s mounted. It’s lightweight and easy to mount using the ¼-20 tapped holes on the back or can also be held into place with just rigid pipe.

siawapp_559x

As the temperatures begin to decline, so does the humidity in the air. Drier air results in an increase in static problems. Get ahead of it this year and check out EXAIR’s wide line of various Static Elimination products, all available to ship same-day from stock!

Tyler Daniel
Application Engineer
E-mail: TylerDaniel@exair.com
Twitter: @EXAIR_TD