Tag: refrigerant dryer

Intelligent Compressed Air: Refrigerant Dryers

Published on by Tyler DanielLeave a comment

When we talk with customers about their EXAIR Products, we also discuss the quality of their compressed air. Many of our products have no moving parts and are considered maintenance-free when supplied with clean, moisture free compressed air. One of the most critical aspects of a compressed air distribution system is the dryer.

No matter where you are in the world, the atmospheric air will contain water vapor. Even in the driest place in the world, McMurdo Dry Valley in Antarctica, there is some moisture in the air. As this air cools to the saturation point, also known as dew point, the vapor will condense into liquid water. The amount of this moisture will vary depending on both the ambient temperature and the relative humidity. According to the Compressed Air Challenge, a general rule of thumb is that the amount of moisture air can hold at a saturated condition will double for every increase of 20°F. In regions or periods of warmer temperatures, this poses an even greater problem. Some problems that can be associated with moisture-laden compressed air include:

  • Increased wear of moving parts due to removal of lubrication
  • Formation of rust in piping and equipment
  • Can affect the color, adherence, and finish of paint that is applied using compressed air
  • Jeopardizes processes that are dependent upon pneumatic controls. A malfunction due to rust, scale, or clogged orifices can damage product or cause costly shutdowns
  • In colder temperatures, the moisture can freeze in the control lines

In order to remove moisture from the air after compression, a dryer must be installed at the outlet of the compressor. It is recommended to dry the compressed air to a dew point at least 18°F below the lowest ambient temperature to which the distribution system or end use is exposed. A dew point of 35-38°F is often sufficient and can be achieved by a refrigerated dryer (Best Practices for Compressed Air Systems). This makes the refrigerant dryer the most commonly used type in the industry.

A refrigerant dryer works by cooling the warm air that comes out of the compressor to 35-40°F. As the temperature decreases, moisture condenses and is removed from the compressed air supply. It’s then reheated to around ambient air temperatures (this helps to prevent condensation on the outside of distribution piping) and sent out to the distribution system.

With your air clean and dry at the point of use, you’re making sure you get the most out of EXAIR’s Intelligent Compressed Air Products without adhering to pesky maintenance procedures.

Tyler Daniel
Application Engineer
E-mail: TylerDaniel@EXAIR.com
Twitter: @EXAIR_TD

Compressor image courtesy of Tampere Hacklab via Flickr Creative Commons License

What Are Compressed Air Dryers and Why are They Necessary?

Published on by Tyler DanielLeave a comment

desiccant-dryer

When we talk with customers about their EXAIR Products, we also discuss the quality of their compressed air. Many of our products have no moving parts and are considered maintenance-free when supplied with clean, dry compressed air. One of the most critical aspects of a compressed air distribution system is the dryer.

No matter where you are in the world, the atmospheric air will contain water vapor. Even in the driest place in the world, McMurdo Dry Valley in Antartica, there is some moisture in the air. As this air cools to the saturation point, also known as dew point, the vapor will condense into liquid water. The amount of this moisture will vary depending on both the ambient temperature and the relative humidity. According to the Compressed Air Challenge, a general rule of thumb is that the amount of moisture air can hold at a saturated condition will double for every increase of 20°F. In regions or periods of warmer temperatures, this poses an even greater problem. Some problems that can be associated with moisture-laden compressed air include:

  • Increased wear of moving parts due to removal of lubrication
  • Formation of rust in piping and equipment
  • Can affect the color, adherence, and finish of paint that is applied using compressed air
  • Jeopardizes processes that are dependent upon pneumatic controls. A malfunction due to rust, scale, or clogged orifices can damage product or cause costly shutdowns
  • In colder temperatures, the moisture can freeze in the control lines

In order to remove moisture from the air after compression, a dryer must be installed at the outlet of the compressor. There are three primary types of dryers used in the compressor industry: refrigerant, desiccant, and membrane. Each style has it’s own inherent applications and benefits.

Refrigerant type dryers cool the air, removing the condensed moisture before allowing it to continue through the distribution system. These will generally lower the dew point of the air to 35-40°F which is sufficient for most applications. So long as the temperature in the facility never dips below the dew point, condensation will not occur. Typical advantages of a refrigerant dryer include: low initial capital cost, relatively low operating cost, and low maintenance costs. This makes them a common solution used in an industrial compressed air system.

Another type of dryer is the desiccant dryer. I’m sure you’ve seen the small “Do Not Eat” packages that are included in a variety of food products, shoes, medications, etc. These are filled with a small amount of desiccant (typically silica gel) that is there to absorb any moisture that could contaminate the product. In a desiccant dryer, the same principle applies. The compressed air is forced through a “tower” that is filled with desiccant. The moisture is removed from the air supply and then passed into the distribution system. One minor drawback with a desiccant type dryer is that the desiccant material does have to periodically be replaced. Desiccant dryers can also be used in addition to a refrigerant dryer for critical applications that require all water vapor to be removed.

The third type of dryer is the membrane dryer. In this style, extremely low dew points are able to be achieved. This makes them the optimal choice for outdoor applications where the air could be susceptible to frost in colder climates. They are also ideal for medical and dental applications where consistent reliability and air quality is an absolute must. A membrane dryer does not require a source of electricity to operate and its compact size allows it to be easily installed with minimal downtime and floor space. Maintenance is minimal and consists of periodic replacement of the membrane. While they are good for some applications, they do come with limitations. They do limit the capacity of the system with variations ranging from as little as 1 SCFM to 200 SCFM. Because of this, they’re often used as a point-of-use dryer for specific applications rather than an entire compressed air system. Some of the compressed air must be purged with along with the moisture which consumes excess compressed air.

Regardless of what products you’re using at the point-of-use, a dryer is undoubtedly a critical component of that system. Delivering clean, dry air to your EXAIR Products or other pneumatic devices will help to ensure a long life out of your equipment.

Tyler Daniel
Application Engineer
E-mail: TylerDaniel@EXAIR.com
Twitter: @EXAIR_TD

About Compressed Air Dryers – What Are They and Why Use Them

Published on by Leave a comment

All atmospheric air contains some amount of water vapor.  When air is then cooled to saturation point, the vapor will begin to condense into liquid water. The saturation point is the condition where the the air can hold no more water vapor. The temperature at which this occurs is knows as the dew point.

When ambient air is compressed, heat is generated and the air becomes warmer. In industrial compressed air systems, the air is then routed to an aftercooler, and condensation  begins to take place. To remove the condensation, the air then goes into separator which traps the liquid water. The air leaving the aftercooler is typically saturated at the temperature of the discharge, and any additional cooling that occurs as the air is piped further downstream will cause more liquid to condense out of the air. To address this condensation, compressed air dryers are used.

It is important to dry the air and prevent condensation in the air. Many usages of the compressed air are impacted by liquid water being present. Rust and corrosion can occur in the compressed air piping, leading to scale and contamination at point -of -use processes. Processes such as drying operations and painting would see lower quality if water was deposited onto the parts.

dryers.png

There are many types of dryers – (see recent blogs for more information)

  • Refrigerant Dryer – most commonly used type, air is cooled in an air-to-refrigerant heat exchanger.
  • Regenerative-Desiccant Type – use a porous desiccant that adsorbs (adsorb means the moisture adheres to the desiccant, the desiccant does not change, and the moisture can then be driven off during a regeneration process).
  • Deliquescent Type – use a hygroscopic desiccant medium that absorbs (as opposed to adsorbs) moisture. The desiccant is dissolved into the liquid that is drawn out. Desiccant is used up, and needs to be replaced periodically.
  • Heat of Compression Type – are regenerative desiccant dryers that use the heat generated during compression to accomplish the desiccant regeneration.
  • Membrane Type– use special membranes that allow the water vapor to pass through faster than the dry air, reducing the amount water vapor in air stream.

The air should not be dried any more than is needed for the most stringent application, to reduce the costs associated with the drying process. A pressure dew point of 35°F to 38°F (1.7°C to 3.3°C) often is adequate for many industrial applications.  Lower dew points result in higher operating costs.

If you have questions about compressed air systems and dryers or any of the 15 different EXAIR Intelligent Compressed Air® Product lines, feel free to contact EXAIR and myself or any of our Application Engineers can help you determine the best solution.

Brian Bergmann
Application Engineer
Send me an email
Find us on the Web 
Like us on Facebook
Twitter: @EXAIR_BB