Webinar by EXAIR: Use This, Not That – Four Common Ways to Save Compressed Air in Your Plant

UThisThat_LIVEOD_600x150

Not much in life is free anymore. So, make sure and take advantage of EXAIR’s upcoming FREE webinar at 2:00 PM ET on 10/17/2019. Not only are we providing it for free, but in this webinar we’ll be discussing how you can save money by reducing your compressed air consumption. Something for free, that will help save you money? Almost unheard of these days!!! Hosted by one of our highly-trained Application Engineers, Jordan Shouse, you’ll learn about four common ways that you can easily save air in your facility.

Compressed air is often referred to as the fourth utility in industry. When used improperly, compressed air is extremely expensive. Homemade devices such as open-ended and drilled pipes, inefficient air nozzles, leaks, etc. all contribute to increased energy costs. In addition to being wasteful, these devices are not safe and compliant with OSHA standards and regulations. By using an Intelligent Compressed Air Product, you’ll be both saving money and creating a safer environment for your operators.

In this webinar, you’ll gain an understanding of the places in your facility that are wasting the most compressed air. We’ll educate you on the various engineered solutions available from EXAIR to help eliminate unnecessary compressed air usage. You’ll gain the knowledge necessary to determine the best solution based on the application, sound level, compressed air usage, and compliance with OSHA safety requirements. You’ll also learn about the various solutions available to help understand and optimize your compressed air system. You can’t begin implementing a plan to reduce air consumption until you fully understand the usage in your own facility and processes. EXAIR’s line of Optimization products are ideal to help you gain a baseline measurement and begin implementing new products and processes that’ll only help add to your bottom line.

UThisThat_OD_552x368

After the conclusion of the webinar will be a brief Q&A session where you can ask any questions you have about any of the topics covered. Unable to attend the webinar live? Don’t let that stop you from registering! Afterwards, each registrant will receive a link via e-mail where they’ll be able to access the full webinar at any time. Make sure and take advantage of this opportunity to gain some knowledge about the usage of your compressed air. You’ll be glad you did!

Tyler Daniel
Application Engineer
E-mail: TylerDaniel@EXAIR.com
Twitter: @EXAIR_TD

Tiny Engineered Nozzle Saves 91 SCFM for Engine Block Blow-Off

Drilled pipe
Air Box with homemade nozzles

Above, you see a photo of what our customer calls an “air box”. It is aptly named as it consists of approximately 65 homemade nozzles, connected to a large plenum, which are able to be aimed in a variety of directions to blow out the numerous holes that are machined into the bottom of an aluminum engine block.

The engine (1024x621)
Engine Block with multiple holes to be blown out

Each of the nozzles above were hand-made for the air box fixture with an internal hole diameter of 1.6 mm. and which produced a force of about 50 grams with 6 BARG inlet pressure. The goal of reviewing the application was to see what if any EXAIR nozzles could replace these custom-made units to produce an air savings and thus cost savings for operating their fixture.

1108ss_profile
Model 1108SS Super Air Nozzle

After determining that the existing nozzles consumed 4.1 SCFM @ 6 BARG inlet pressure, I was able to make a comparison to the Super Air Nozzles that make up the smaller end of our flow range. In comparing these nozzles, I was able to determine that the Atto Super Air Nozzle, model 1108SS consumes 2.69 SCFM @ 6 BARG and produces 61 grams of force per nozzle.

The calculated air savings between the existing nozzle and the EXAIR Super Air Nozzle was about 34%. That’s a savings of 1.4 SCFM per nozzle. In terms of sheer air volume, that’s not a lot, BUT when you multiply that up over 65 nozzles, total air savings is 91 SCFM. That is close to saving the full output of a 25 HP air compressor!

And so, if you run out the cost to operate a 25 HP air compressor for a year’s worth of production, the savings becomes quite clear that by simply swapping out these homemade nozzles for an engineered solution with EXAIR Super Air Nozzles, the customer can achieve their goal for reduction in air use. Not to mention a significant reduction in the noise level for the application as well as enhanced safety with OSHA compliant nozzles.

Do you have a blowing application that could benefit from the same kind of simple, swapping of nozzles to bring your production costs down? Give us a call and let us know about your application. We would be happy to discuss with you and provide a similar comparison to determine how much air you could save!

Neal Raker, International Sales Manager
nealraker@exair.com
@EXAIR_NR