6 Important Factors when Choosing a Safety Air Gun

If you look at operating costs alone, compressed air can be just about the most inefficient method there is for cleaning parts. If you just look at the risks, it’s potentially very dangerous too. Don’t even get me started on the insufferable noise it can make.

For cleaning parts, most folks are familiar with the use of an air gun. You can find the simplest of these in many industrial settings: a valve (often in the form of a handheld trigger device) fitted with a nozzle of some sort (often in the form of an open ended tube, pipe, or fitting to focus or direct the air flow). These have all three of the “downsides” I opened this blog with. Of course, these concerns can be mitigated to a high degree by using the right tool for the job. That’s where engineered products like EXAIR Safety Air Guns come in. Let’s look at how we can address these three “downsides”:

Efficiency: This is all about compressed air consumption. In the simplest of air guns mentioned above, consumption is only limited by the passages in the valve (or trigger) and the discharge fitting…and those limits are usually negligible. Modifying the ends (see examples below) to focus the air flow usually has minimal effect, because you’re not appreciably changing the total cross sectional area of the discharge opening:

Here are a few modified thumb trigger air guns that were sent in for Efficiency Lab testing. Left to right, compressed air consumption at 80psig supply pressure was 34.2 SCFM, 30.9 SCFM, and 28.2 SCFM. For comparison (more on this later,) EXAIR Model 1210 Soft Grip Safety Air Gun uses only 14 SCFM and generates a very similar flow pattern.

Safety: Remember learning about kinetic and potential energy in grade school? Well, when you compress air to 100psig, fitting all that air into a much smaller space creates a TREMENDOUS amount of potential energy:

The block on the left represents a cubic foot of air at atmospheric pressure. The one on the right represents how much space the first one takes up when compressed to 100psig. The energy imparted by this process HAS to be handled with care.

One problem with the thumb guns above is, if you were to jam into the palm of your hand and pull the trigger, a large component of that potential energy (pressure) turns into kinetic energy (force)…more than enough to break the skin and cause a potentially fatal condition known as an air embolism. In the United States, OSHA (Occupational Safety and Health Administration) regulates compressed air devices used for cleaning purposes. All EXAIR Safety Air Guns comply with Standard 1910.242(b) by providing a relief path to ensure that it cannot be dead ended, and thus never create over 30psi measurable at the outlet)

EXAIR Super Air Nozzles cannot be dead ended, ensuring the outlet pressure won’t reach OSHA limits, regardless of supply pressure.

Noise: Another problem is, another component is turned into sound pressure…discharging air from a direct opening is quite loud. OSHA standards address these with limitations on outlet pressure and sound level. All EXAIR Safety Air Guns comply with Standard 1910.242(b), which limits the outlet pressure (by providing a relief path to ensure that it cannot be dead ended, and thus never create over 30psi measurable at the outlet) and all but our largest Super Blast Safety Air Guns comply with Standard 1910.95(a) limits for continuous 8 hour sound level exposure.

Which brings us to the topic of this blog: How exactly did THEY (our customer who used to use the thumb guns above) select the right Safety Air Gun, and how can we apply that to getting the right Safety Air Gun for YOU?

These steps aren’t all-inclusive, and they don’t necessarily need to be followed in order, but if you call an EXAIR Application Engineer about selecting a Safety Air Gun, here’s what we’re gonna talk about:

Ergonomics: We offer five distinctive styles of Safety Air Guns:

From small part cleaning by hand, to wide area blowoff, and all points in between, EXAIR has a Safety Air Gun for most any application.

Our thumb gun user (as I alluded to above) chose the Model 1210 Soft Grip Safety Air Guns (top right). They had a number of typical industrial applications where the operators had the parts or surfaces to be blown off right in front of them. They liked the integral storage hook and rubberized hand grip, but the VariBlast Compact (top middle) or Heavy Duty Safety Air Guns (bottom left) were also considered. The VariBlast Precision (top left) and Super Blast Safety Air Guns (bottom right) were too focused or more powerful, respectively, than needed.

Airflow pattern: Honestly, I could make a good case for this being the first consideration. Selection of any blowoff product – be it an Air Nozzle, Air Amplifier, Air Knife, Air Wipe, etc., will largely depend on the size and shape of the airflow.

variety of airflow patterns…and effective distances…are available from EXAIR’s comprehensive line of Super Air Nozzle products.

Application specific concerns: Everything we’ve discussed so far has involved aiming the blow off stream away from the operator, in the direction the device is aimed. In addition to wide variety of engineered Air Nozzles, EXAIR offers a number of options for these products:

Atto Back Blow Nozzles can blow out recesses or holes as small as 1/4″ in diameter.
Scrape off, and blow away, stubborn debris with the Model 1244-48 Soft Grip Super Air Scraper.

If you’re looking for a portable, hand-held compressed air blow off product that’s quiet, safe, and efficient, look no further than EXAIR Corporation’s extensive line of Safety Air Guns. If you’d like to find out more, give me a call.

Russ Bowman, CCASS

Application Engineer
EXAIR Corporation
Visit us on the Web
Follow me on Twitter
Like us on Facebook

Safety Air Guns: Chip Shields, Extensions, and More

Over the last several weeks, you may have read blog posts regarding the EXAIR Safety Air Guns.  You can find the blogs here, here and here. We are also in the midst of a Safety Air Gun Promotion, please click HERE for more details on how you can get a free 1″ Flat Super Air Nozzle. Today, I want to review a few available options for the Safety Air Guns.

Protect Workers From Flying Debris! – Chip Shields are durable polycarbonate shields that protect the operator from flying debris often seen when blowing off chips from machined parts. They are also useful to prevent coolant from splashing back, creating a mess during drying processes.

Chip Shields
Chip Shields

The Chip Shields are available for EXAIR’s VariBlast, Soft Grip, and Heavy Duty Safety Air Guns. The Chip Shield can be used on Safety Air Guns with or without an aluminum extension. They may be purchased as part of a new air gun system, or retrofitted as a Chip Shield Kit.  Consult an Application Engineer for selection assistance.

 

If you have a blow-off process where the air is to be directed at a distance away from the operator, or into a hard to reach location an extension is the solution. Available in lengths from 6″ (152mm) to 72″ (1829mm), with sizes as shown below, a length to meet most any requirement can be found. To add an extension to an air gun, simply add -xx to the current part number.

extensions
Aluminum Extensions, Available in Sizes of 6″ (152mm) up to 72″ (1829mm)

1210-6-CS
Model 1210-6-CS, a model 1210 Soft Grip Safety Air Gun, with 6″ Extension and Chip Shield

And, if you need a 12′ coiled air hose, to use with your Safety Air Gun, we have them available and in stock. Available with 1/8 NPT, 1/4 NPT or 3/8 NPT male end swivel connections. Avoid tangled and messy air lines and keep things neat!

Coiled Hose
Coiled Hose, 12′ Long, With 1/8 NPT, 1/4 NPT or 3/8 NPT Male Swivel Connections

To discuss your application and how an EXAIR Intelligent Compressed Air Product can improve your process, feel free to contact EXAIR, myself, or one of our other Application Engineers. We can help you determine the best solution!

Brian Bergmann
Application Engineer

Send me an email
Find us on the Web 
Like us on Facebook
Twitter: @EXAIR_BB

Safety Air Guns – Using Engineered Air Nozzles For High Performance

Inexpensive air guns can be picked up just about anywhere, and you generally get what you pay for. Most will be very noisy and waste lots of compressed air.  And many will be unsafe, violating two of OSHA’s standards put in place to protect worker safety. The first is Standard 29 CFR 1910.95(a) which sets limits to the maximum noise exposure, and the second is Standard 29 CFR 1910.242(b) which says that the nozzle cannot be dead-ended, or exceed a 30 PSIG pressure limit.

These guns may seem like a perfect fit for a handheld blowoff application. The truth is, the cost saved up front will easily be paid throughout the cost of ownership.  This is due to the lack of an engineered nozzle which meets and exceeds the OSHA standards mentioned above.   The “cheap” guns often have a cross drilled hole to meet or exceed the OSHA standard for dead-end pressure. While this may be true, it causes a large wind sheer which escalates noise levels to well over the allowable noise level exposure set by OSHA.  These tips sometimes offer large force outputs because they are equivalent to an open pipe.  We have publicized numerous times about how an open pipe blow off does not permit pressure to be utilized all the way to the point of blowoff, and is also a waste of energy.

In order to determine how much compressed air your current blow guns utilize, the level of noise they product, and the sound level they produce, consider taking advantage of the EXAIR Efficiency Lab.  The Efficiency Lab is a free service that you can read more about here.

An EXAIR Safety Air Gun is engineered and designed to comply both of the OSHA standards mentioned above, ensuring safe operation for company personnel.  On top of the safety designed into the guns, we also ensure all of our guns are efficient by offering only engineered nozzles on them.

EXAIR offers (4) types of Safety Air Guns – the VariBlast, the Soft Grip, the Heavy Duty, and the Super Blast.  Each type of Safety Air Gun is offered with a plethora of nozzles, as well as varying length extensions, with or without the Chip Shield.

Safety Air Guns
The VariBlast, Soft Grip and Heavy Duty Style of Pistol Grip Safety Air Guns

Super Blast
The Super Blast Style of Safety Air Gun

 

We invite you to try out an EXAIR Safety Air Gun, and get the free 1″ Wide Flat Super Air Nozzle as a bonus. Click here for more details about this special promotional offer.

To discuss your application and how an EXAIR Intelligent Compressed Air Product can improve your process, feel free to contact EXAIR, myself, or one of our other Application Engineers. We can help you determine the best solution!

Brian Bergmann
Application Engineer

Send me an email
Find us on the Web 
Like us on Facebook
Twitter: @EXAIR_BB

EXAIR Safety Air Gun Promotion

From August 1st to September 30th, 2018, EXAIR will be giving away a 1” Flat Super Air Nozzle with the purchase of any promotional VariBlast, Soft Grip, or Heavy Duty Safety Air Gun.  EXAIR is stressing the importance of safety in the workplace with the EXAIR Safety Air Guns as well as the versatility of the different types of EXAIR Super Air Nozzles.

SAGpromoAD_500xsq

This promotional item, the model 1126 1″ Flat Super Air Nozzle, has a patented shim to blow a 1” wide stream of air to clean surfaces quickly and efficiently and is a $45.00 USD value. For more details on the Promotion, click on the photo/link above. For more information about the Flat Super Air Nozzles, click HERE.

Inexpensive air guns can be purchased just about anywhere- online, via catalogs, and through industrial supply companies. Typical quality is less than ideal – broken triggers, leaky valves – a short lifespan in an industrial setting are merely a few of the issues observed.  Most are loud and inefficient – they just blow large amounts of compressed air, and at noise levels that violate OSHA requirements.  Some may even generate dangerous dead end pressure situations that that can result in serious or fatal injuries if blocked.

EXAIR’s Safety Air Guns have been engineered and designed to eliminate these issues. They are durable for use in industrial situations and comfortable to use for extended periods of time.  With an EXAIR engineered air nozzle, each model provides top performance by entraining large volumes of surrounding air into the air-stream. Operation is assured to be safe along with low compressed air consumption and noise levels.  Due to the design, the airflow that exits the nozzle cannot be blocked, as required by OSHA Standard 29 CPR 1910.242(b).

Safety Air Guns
The EXAIR VariBlast, Soft Grip and Heavy Duty Safety Air Guns

The VariBlast style of safety air gun offers variable force based on the range of trigger pull. Force can be varies, form a light breeze, to full force maximum output. This cast aluminum air gun can be fitted with any of the EXAIR 1/8 NPT engineered air nozzles.

The Soft Grip style of safety air gun  has a durable cats aluminum body suited for rugged, industrial use. The ergonomic design has a soft vinyl cover, a large trigger for easy operation, and a hanger hook for easy storage.

The Heavy Duty style of safety air gun is powerful with a durable aluminum cast body and ergonomic composite rubber grip, best suited for rugged industrial environments. Hours of fatigue free operation are possible.

With all of the Safety Air Guns styles, Chip Shields and Extension Pipes are available, from 6″ to 72″ in length.

1210-6cs
Soft Grip Safety Air Gun, with Chip Shield and 12″ Extension

With many nozzle options, from a whisper quiet 58 dBA and 2.5 SCFM of flow up to 60 SCFM and 87 dBA (still below the OSHA 8 hour noise level threshold) there is a model that will fit practically any application. Application Engineers are available by phone, email, and chat to review your specific blow off needs, and help to select the best possible solution available.

We invite to you to try out an EXAIR Safety Air Gun, and get the free 1″ Wide Flat Super Air Nozzle as a bonus.

To discuss your application and how an EXAIR Intelligent Compressed Air Product can improve your process, feel free to contact EXAIR and myself or one of our other Application Engineers can help you determine the best solution.

Brian Bergmann
Application Engineer

Send me an email
Find us on the Web 
Like us on Facebook
Twitter: @EXAIR_BB