Benefits of Atomized Liquid Nozzles vs. Liquid Nozzles

There are a great many applications that require a spray (as opposed to a stream) of liquid. Certain droplet sizes, and flow rates, are beneficial for certain applications. For example, if you’re fighting a fire, you want as high of a flow rate as possible – the more water you douse the fire with, the quicker it goes out.  You also want a fairly large droplet size, since a mist would tend to evaporate instead of extinguishing the flames.

Pressure washers also benefit from higher (though not near as high as fire hose) flow rates, and droplet sizes.  You want an appreciable flow rate, because that means high velocity, and good sized droplets combine that velocity with their relative mass to “blast” away dirt and detritus from the surface.

Medicine delivery devices, like asthma inhalers, are designed to produce mid-sized droplets, but pretty low (and controlled) flows.  The droplets need to be small enough to efficiently spread the medicine through the breathing passages, but large enough to where they won’t evaporate before they ‘plant’ on the nasal & bronchial membranes to get absorbed.

These are examples of “liquid-only” nozzles…no other media or means of force are used to effect the spraying action.  Most of the time, the droplet sizes in these applications are measured in hundreds of microns, which “liquid-only” nozzles are ideally suited to generate.  Other applications, however, call for much smaller droplet sizes…such as those only attainable through atomization.

EXAIR Atomizing Spray Nozzles use compressed air to create a fine mist of liquid, with droplet sizes as low as 22 microns.

A typical “liquid-only” nozzle is capable of producing droplet sizes of 300-4,000 microns. Atomizing Nozzles’ droplet sizes are consistently under 100 microns, and can be as small as 20 microns!

Small droplet size is key to cost effectiveness in many applications:

  • Think about expensive coatings…the smaller the droplet size, the better and more even the coverage, and the less you have to spray (and pay) out.
  • Or humidification…smaller droplet size means more stays airborne, for longer, and in a larger space.
  • Petroleum based lubricants, by their nature, only require a thin layer for best results.  Smaller droplets make as even and thin of a layer as possible.
  • Dust control is much more effective with smaller droplet sizes, since the longer the mist lingers in the air, the more dust particles the individual droplets will adhere to…and then drop with them to the surface.  This also prevents getting the surface of the material any wetter than it has to be.
142 distinct models. 8 different patterns. Liquid flow rates from 0.1 to 303 gallons per hour. If you’ve got a spraying application, EXAIR has an Atomizing Nozzle for you!

If you’d like to discuss a liquid spraying application, I’d love to hear from you.  Call me.

Russ Bowman
Application Engineer
EXAIR Corporation
Visit us on the Web
Follow me on Twitter
Like us on Facebook

Intelligent Compressed Air: Refrigerant Dryers and How They Work

We’ve seen in recent blogs that Compressed Air Dryers are an important part of a compressed air system, to remove water and moisture to prevent condensation further downstream in the system.  Moisture laden compressed air can cause issues such as increased wear of moving parts due to lubrication removal, formation of rust in piping and equipment, quality defects in painting processes, and frozen pipes in colder climates.  The three main types of dryers are – Refrigerant, Desiccant, and Membrane. For this blog, we will review the basics of the Refrigerant type of dryer.

All atmospheric air that a compressed air system takes in contains water vapor, which is naturally present in the air.  At 75°F and 75% relative humidity, 20 gallons of water will enter a typical 25 hp compressor in a 24 hour period of operation.  When the the air is compressed, the water becomes concentrated and because the air is heated due to the compression, the water remains in vapor form.  Warmer air is able to hold more water vapor, and generally an increase in temperature of 20°F results in a doubling of amount of moisture the air can hold. The problem is that further downstream in the system, the air cools, and the vapor begins to condense into water droplets. To avoid this issue, a dryer is used.

Refrigerated Dryer
Fundamental Schematic of Refrigerant-Type Dryer

Refrigerant Type dryers cool the air to remove the condensed moisture and then the air is reheated and discharged.  When the air leaves the compressor aftercooler and moisture separator (which removes the initial condensed moisture) the air is typically saturated, meaning it cannot hold anymore water vapor.  Any further cooling of the air will cause the moisture to condense and drop out.  The Refrigerant drying process is to cool the air to 35-40°F and then remove the condensed moisture.  The air is then reheated via an air to air heat exchanger (which utilizes the heat of the incoming compressed air) and then discharged.  The dewpoint of the air is 35-40°F which is sufficient for most general industrial plant air applications.  As long as the compressed air stays above the 35-40°F temperature, no further condensation will occur.

The typical advantages of Refrigerated Dryers are-

  1.  – Low initial capital cost
  2.  – Relatively low operating cost
  3.  – Low maintenance costs

If you have questions about getting the most from your compressed air system, or would like to talk about any EXAIR Intelligent Compressed Air® Product, feel free to contact EXAIR and myself or one of our Application Engineers can help you determine the best solution.

Brian Bergmann
Application Engineer

Send me an email
Find us on the Web 
Like us on Facebook
Twitter: @EXAIR_BB