Siphon Fed Atomizing Nozzle Improves Roll Forming Process

Last week I worked with a gutter manufacturer who was looking for a way to spray a light coating of vanishing oil on the rollers of a forming machine. Roll forming is commonly used when needing to maintain a constant and consistent shape or feature across the length of the part. In this particular case, a sheet of aluminum, used as a cover for the gutter, is fed into the machine where it passes over a series of dyes that bends “ribs” and punches small holes into the part to keep leaves or debris from settling on top, while allowing the rainwater to pass through the holes and into the gutter.

They were needing to apply the oil to the rollers because they were starting to see some irregularities in hole size as well as some deformities to the shape of the ribs due to heat being generated during the forming process. The customer was interested in using some type of atomizing spray nozzle in the hopes that providing an atomized mist of liquid may provide for a faster evaporation of the oil so there wasn’t much residue left on the part before packaging.

After further discussing the details, they advised that they were going to have the oil in a container about 12″ below the machine but didn’t have a way to pressurize or pump the liquid to the nozzle. Once again, EXAIR has the perfect solution with our 1/4 NPT Siphon Fed Atomizing Nozzles. These nozzles are the ideal solution where pressurized liquid isn’t available as they use the compressed air to the draw the liquid into the nozzle, up to 36″ of suction height, and mix it internally to produce a mist of atomized liquid spray. For this particular application, the Model # SR1010SS was a good solution as it provides a low flow rate of only 0.8 GPH and a tight spray pattern to focus right at the rollers to avoid any waste or overspray.

sr1010ss

Model # SR1010SS Siphon Fed Round Pattern Atomizing Spray Nozzle – 303ss construction, fully adjustable flow rate

EXAIR offers an extensive range of Atomizing Nozzles that can be used for light coating applications, like above, or for wider coverage areas or higher flow rates. For help selecting the best option to fit your needs, contact one of our application engineers for assistance.

Justin Nicholl
Application Engineer
justinnicholl@exair.com
@EXAIR_JN

Internal Mix Atomizing Nozzle for Roll-forming Application

20160603_090706_001

Roll-formed metal stud material

Our distributor from South Africa contacted me recently with a problem that one of his customers were having with their roll forming process. Their business is making metal studs used for erecting walls and covering with drywall. The metal studs start out as a 200 mm wide x 0.5 mm thick roll of sheet metal. The customer feeds the sheet metal through a series of rolling dies that gradually impart the final shape of a metal stud to the material. During this process, a lubricant is applied through a couple of metal pipes with drilled holes in them to disperse the lubricant onto the metal sheet.

The problem with the application is that it makes a total mess because there aren’t any controls on the fluid flow to keep the application rate where it needs to be. All they need is a light coating of the lubricant. What they’re getting now is a constant drizzle from multiple holes. Not only is this wasteful for the use of the lubricant, it causes a huge mess in the form of puddled lubricant on the floor. This problem also presents a slip and fall hazard to the operators as well. See the photo below.

 

 

20160603_090732

Application of lubricant through drilled, metal pipe

In an effort to help them, my friend Wayne contacted me about the situation and presented a couple of scenarios he had in mind. One was to keep the existing system in place and use a couple of Super Air Knives to blow off the excess lubricant into a catch basin. The other was to apply a couple of our Internal Mix, Wide, Flat Atomizing nozzles into the application to provide a fine spray of the lubricant on both sides of the sheet metal.

After asking a few questions about whether the liquid was under any sort of pressure, its viscosity and the desired application rate I suggested to Wayne that the customer go with (2) pieces of model AF1010SS Internal Mix, Flat Fan Atomizing Nozzle. This Atomizing nozzle is more than adequate to provide the customer with the precise amount of the lubricant onto the sheet metal just prior to forming. The point in recommending the atomizing nozzles is to conserve the customer’s lubricant when it is applied in the first place so that they don’t have the huge mess that ends up developing during continuous operation. In this way, they are not treating a symptom of the problem by blowing the excess lubricant with a Super Air Knife, but rather tackling the problem right at its source by choking back on the application of the fluid in the first place.

After the customer installed their nozzles and made a production run, they were able to dial the application rate in to exactly what they needed. The mess and safety hazard went away and the customer was able to cut their lubricant use by half so far. They say they will continue to try and optimize its use as saving the lubricant used represented a nice cost savings to the customer that they had not thought about prior to engaging our distributor to help them take away this headache. They were simply concerned about the mess in the beginning.

It’s always nice to have such positive knock-on effect when you make process improvements like this.

Neal Raker, International Sales Manager
nealraker@exair.com
@EXAIR_NR

 

%d bloggers like this: