6″ Super Ion Air Knife Provides Separation Of Solar Panel Plates

I was recently working with a solar energy research center who was experiencing a static issue with their solar panel building process. They currently take a stack of small, silicon wafer plates, measuring approximately 6″ long X 6″ wide and 2 mm thick, and take the top plate from the stack and place it on the assembly table. The issues they were experiencing was that when they went to lift the top plate, static was making the plates cling together, resulting in several plates being picked up at one time. In some cases, they were able to get separation, but were seeing dust and dirt settle on the surface. This was causing two negative effects. First, when the plates get stuck together, they try to manually separate them which would cause them to crack or completely break. If they did get them separated without cracks, the second issue was contamination from foreign particulate would cause an operator to have to manually clean the plate, prolonging the assembly and reducing the daily production. Trying to remedy the situation, they decided to use a small open airline blowing at the side of the plates to get separation between the plates as they are lifted. While this did help a little with separation it did not remedy the particulate issue and they still weren’t able to achieve a desired result.

OLYMPUS DIGITAL CAMERA

Built Solar Panels

I recommended the customer use our Model # 111206, 6″ Super Ion Air Knife Kit in the application. The Super Ion Air Knife is our Super Air Knife with an Ionizing Bar attached to produce a laminar sheet of ionized air across the entire length of the unit. By directing the airflow at the side of the stack, the ionized air would release the static charge, allowing the individual plates to separate and as they are lifted, blow away any remaining unwanted fines on the surface of the plates. In addition, the kit includes a pressure regulator which would allow the customer to increase or decrease the supply pressure, providing some control of the exhaust air velocity and flow so they aren’t moving or disrupting the stack.

Super Ion Air Knife

Super Ion Air Knife produces uniform sheet of ionized air. Available in stocked lengths from 3″ up to 108″.

Justin Nicholl
Application Engineer
justinnicholl@exair.com
@EXAIR_JN

 

Solar Panels image courtesy of Slim Dandy via Creative Commons license.

How To Choose An Air Knife

The EXAIR Super Air Knife has a prominent place near the front of our catalog, and THIRTEEN pages of photos, application details, performance data & specifications. It’s the most efficient and quietest product of its kind on the market, and our most diverse product offering in terms of size range, operational adjustability, materials of construction, and accessories available. For almost any general industrial air blow off application, the EXAIR Super Air Knife is the superior choice in terms of air usage, sound level, and capability.

EXAIR Super Air Knives come in a wide range of lengths, for a wide range of possibilities.

EXAIR Super Air Knives come in a wide range of lengths, for a wide range of possibilities.

As tireless champions of the causes of reducing air consumption and noise, we’re always going to promote these benefits of the Super Air Knife. Still, a caller asked me the other day, “Well, why do you still make the others?”…meaning, of course, our Standard and Full Flow Air Knives. Why, indeed:

*Given the same air supply pressure, the Standard Air Knife generates the highest force of our three styles. The amount of force applied isn’t always a prime consideration…if you think about one of the more “textbook” applications for an Air Knife, it doesn’t take a great amount of force to blow off dust and light debris from a conveyor belt…certainly this is a case where efficiency factors in: the lower air consumption of a Super Air Knife can pay for the cost difference between it and a Standard Air Knife in as little as three months of operation.

The Standard Air Knife has the highest force, for when it's needed.

The Standard Air Knife has the highest force, for when it’s needed.

Of course, if you’re blowing stubborn debris out of tight spaces, like gummy, greasy dirt that’s accumulating in the recesses of a finned tube heat exchanger, that extra force can make all the difference. No; the Standard Air Knife isn’t as efficient or quiet as the Super Air Knife, but it’s still a far cry better than a drilled pipe.

*While the Super Air Knife is pretty compact – you only need a few square inches of profile area to successfully mount it – the Full Flow Air Knife is even smaller, requiring not much more than one square inch of profile for mounting. With ports on the rear face (instead of the ends & bottom for the Super Air Knife,) they can fit in very tight quarters.

Low profile and lightweight, the Full Flow Air Knives are a great fit for tight quarters.

Low profile and lightweight, the Full Flow Air Knives are a great fit for tight quarters.

The Full Flow Air Knife is also the lightest weight for a given length. A 36” Aluminum Super Air Knife, for instance, weighs about 8lbs. The 36” Aluminum Full Flow Air Knife weighs less than 4lbs. Most of the time, 8lbs is a very manageable amount of mass to support, but there are situations where every ounce matters, and if yours is one of them, you’re looking at the Full Flow Air Knife all the way.

*The biggest (in the most literal sense) factor in Air Knife selection is, well…size. We make the Standard Air Knives in lengths to 48”, and the Full Flow Air Knives come as long as 36”. The Super Air Knives, however, are stocked in lengths from 3” to 108”, and can be coupled together for as long of an uninterrupted, steady, laminar air flow as you need.

At the end of the day, a majority of blow off applications can be handled just fine with any of our Air Knives. If you’d like to discuss your application and see which one is best for you, give us a call.

Russ Bowman
Application Engineer
(513)671-3322 local
(800)923-9247 toll free
Find us on the Web
Follow me on Twitter
Like us on Facebook

Chain-Chain-Change, Change Out That Drilled Pipe…

Life is full of change.  It might sound trite, but truer words were never spoken.  I used to get up around 6:30 on work days.  Now, thanks to my son’s middle school schedule, I’m usually seeing him out the door at that time.  Getting up earlier was certainly a difficult change at first, but it’s had its benefits.  Not the least of which is spending a little extra time with the boy in the morning.

One of our favorite things to do while eating breakfast is to watch the ‘How things are made’ types of shows. Of course, watching these types of shows with an engineer has its downside.  While we can usually explain exactly what’s happening in the process of whatever is being made, the problem is that we often do.  Meaning we wind up talking over the program, which, ironically, is one of my greatest pet peeves.  Speaking of change, guess that’s something I need to work on…

20141002_062454

At any rate, this morning we saw a show on making saltines.  At the sight of the copper pipe positioned near where the cracker dough comes off the die-cut wheel, I knew exactly what was up. ‘They’re using drilled pipe! That’s not safe and a HUGE waste of compressed air!  That’s the perfect application for a Super Air Knife!”  Guess watching these programs with an EXAIR engineer has an additional risk: We can get a little over-excited when we see OSHA violations and wastes of compressed air! I think I about made my son jump out of his gym shorts, but he’s watched these sorts of shows with me before.  He knew the risks…

Life is full of change, and while perhaps I can get better at not talking while the TV show is on, I doubt I’ll ever stop cringing at safety violations and wasting compressed air.  Do you have drilled pipe in your plant?  If so, you could be in violation of multiple safety standards and are definitely wasting money on compressed air.  EXAIR can help you minimize harmful noise levels and keep you in compliance with OSHA’s dead-end pressure standard. Please give EXAIR a call to begin saving air and increasing safety!

Dan Preston
Engineer-at-large
DanPreston@exair.com
1-800-903-9247

 

 

%d bloggers like this: