Tag: national institute for occupational safety and health

Measuring and Adding Sounds

Published on by John BallLeave a comment

My colleague, Russ Bowman, wrote a blog about “Sound Power vs Sound Pressure vs Sound Pressure Level”.  He discussed the logarithmic equations around sound.  I will be discussing what happens when you have more than one sound source, as often heard within manufacturing plants.  Sounds can be added together to determine the overall sound level that you hear.  This is very important when it comes to minimizing hearing loss.

In looking at a single source of sound, sound pressure is created by the loudness of a noise.  The units are measured in Pascals.  The lowest pressure perceived by human hearing is 0.00002 Pa, and we can use this value as a reference point.  From sound pressures, we can arrive at a sound pressure level which is measured in decibel, dB.  This correlation between sound pressures and sound pressure levels are calculated by Equation 1:

L = 20 * Log10 (P / Pref)

L – Sound Pressure Level, dB

P – Sound pressure, Pa

Pref – reference sound pressure, 0.00002 Pa

As an example, the sound pressure from a passenger car as heard from the roadside is 0.1 Pa.  With Equation 1, we can get the following decibel level:

L = 20 * Log10 (0.1Pa/0.00002Pa) = 74 dB

Because human ears are sensitive to different frequencies, the sound pressure levels can be modified, or weighted, to indicate an effective loudness level for humans.  This adjustment is done in two different ways; A-weighting and C-weighting.  The C-weighting is for very loud noises with high peaks or sharp impacts like gunfire. The A-weighting is the most used value as the sound pressure levels are adjusted by the frequency level.  For higher and lower frequencies, the change in the sound value is much greater than the mid-level frequencies that are within our hearing range.  Sound measurements for safety are measured on an A-weighted scale.  OSHA created a chart in the standard 29CFR-1910.95(a).  It shows the noise levels over exposure times for an operator.  To use the OSHA chart accurately, the total noise level in dBA should be calculated.

Hearing loss is the best known, but not the only, ill effect of harmful noise exposure. It can also cause physical and psychological stress, impair concentration, and contribute to workplace accidents or injuries.

To determine the total sound level, we can add all the sound pressure levels together by Equation 2:

Equation 2:

Where L1, L2… represents the sound pressure level in dBA for each sound source.

As an example, a manufacturing plant had an operator using a machine that had four copper tubes to blow off a cutting operation (reference photo below).

Blow off station

The decibel level for a copper tube was measured at 98 dBA.  The total amount of sound that the operator was exposed to was determined by Equation 2 with four values.

L = 10 * log10 (109.8 + 109.8 + 109.8 + 109.8)

L = 104 dBA

In looking at the OSHA chart above, the operator would only be allowed to operate the machine only a little over one hour without hearing protection.  In this same example, we replaced the copper tubes with an EXAIR Super Air Nozzle, model 1100SS.  The noise level for each nozzle is 74 dBA at 80 PSIG (5.5 bar).  By replacing all four copper tubes with Super Air Nozzles, Equation 2 becomes:

L = 10 * log10 (107.4 + 107.4+ 107.4 + 107.4)

L = 80 dBA

The total sound level is now in accordance with OSHA regulations for the operator to work all 8 hours at the machine without hearing protection.

A commonly used acronym for hearing safety is NIHL, or Noise Induced Hearing Loss.  To keep your operators safe and reduce NIHL, it is important to measure the total sound level in that area.  As a protocol in safety, it is a requirement to use engineering standards before purchasing personal protective equipment or PPE.  For the customer above, they followed that protocol with our Super Air Nozzles.  If you need to reduce noise levels in your facility, EXAIR offers a large line of blow-off products that can meet the safety requirements.  You can contact an Application Engineer for more information. 

John Ball
Application Engineer
Email: johnball@exair.com
Twitter: @EXAIR_jb

Photo: Ear by PublicDomainPictures  Pixabay License

Industrial Safety: Compressed Air

Published on by John BallLeave a comment

At EXAIR, we have a statement that says, “Safety is everyone’s responsibility.”  EXAIR builds its name around manufacturing safe and protective compressed air products.  In the United States, we have an organization called the Occupational Safety and Health Administration (OSHA) that enforces governmental directives for safe and healthy working environments.  They do training, outreach programs, and educational assistance for manufacturing plants to reduce injuries and fatalities.  They can also enforce these directives with heavy fines for violations.  With compressed air systems, the two most common violations are 29CFR 1910.242(b) for dead-end pressure/chip shielding and 29CFR 1910.95(a) for maximum allowable noise exposure.

Unsafe Nozzle

Here is an example of a nozzle that is dangerous.  As you can see, there is only one path where the air can pass through.  Other similar types of blow-off devices that would fall into this same group would include copper tubes, flexible lines, and open pipes.  They are dangerous as compressed air cannot escape if it is blocked by your body or skin.  If operated above 30 PSIG (2 bar), these nozzles could penetrate the skin and create an air embolism within the body, which can cause bodily harm or death.  This is a hazard that can be avoided by using EXAIR Super Air Nozzles and Safety Air Guns.  The nozzles are designed with fins, which allow the air to escape and cannot be blocked by your skin.  So, you can use the EXAIR Super Air Nozzles safely above 30 PSIG (2 bar) and remain OSHA compliant.

Unsafe Air Gun

To counteract the dead-end pressure violation, some nozzle manufacturers create a hole through the side of the nozzle (reference photo above).  This will allow the compressed air to escape, but now the issue is noise levels.  With an “open” hole in the nozzle, the compressed air is very turbulent and very loud.  The National Institute for Occupational Safety and Health (NIOSH) states that 70% to 80% of all hearing loss within a manufacturing plant is caused by compressed air.  OSHA created a chart to show the maximum allowable noise exposure.  This chart shows the exposure time and noise limits before hearing protection is required.  The EXAIR Super Air Nozzles, Super Air Knives, and Super Air Amplifiers are designed to have laminar flow, which makes them very quiet.  As an example, the model 1210 Soft Grip Safety Air Gun has a sound level of only 74 dBA, well under the noise exposure limit for 8 hours.

One of the last things that companies think about when purchasing compressed air products is safety.  Loud noises and dead-end pressure can be missed or forgotten.  To avoid any future fines or having to purchase additional personal protective equipment (PPE), it will be much safer to purchase EXAIR products.  If you would like to improve the safety of your facility and reduce energy costs, an Application Engineer at EXAIR can review your current blow-off devices.  Remember, safety is everyone’s responsibility. 

John Ball
Application Engineer
Email: johnball@exair.com
Twitter: @EXAIR_jb

Photo: Industrial Security Signal by DavidRockDesign.  Pixabay license

Reduce Noise Exposure with Super Air Nozzles

Published on by Russ BowmanLeave a comment

News from the CDC that those of us involved with industrial safety are paying close attention to is the release of their NIOSH (National Institute for Occupational Safety and Health) division’s Hazard Evaluation Program Noise Measurement Database, which contains data obtained through Health Hazard Evaluation surveys performed between 1996 and 2012. It includes hundreds of personal noise exposure measurements (how much noise was received by individuals) and almost as many area noise measurements (how much noise was made.) A comparison of these measurements, of course, is valuable in determining if appropriate measures are being taken to abate the exposure, which is key: there are an awful lot of industrial processes where there’s nothing that can be done about the generation of noise…they’re just simply LOUD. So, they focus on what they can do to limit exposure: Use engineering controls (retrofit open line with engineered nozzles, build sound barriers) , use administrative controls (relocating personnel away from the sound), use personal protective equipment, and spending as little time as possible near the source.

Regardless of what people can get used to, the area noise associated with compressed air use CAN be reduced, while still maintaining the efficiency of the operation. Here’s the deal:

*The most basic form of air blow off is a piece of pipe, tubing, or hose connected to a source of compressed air. When it’s opened to the atmosphere, the compressed air exits with a great deal of force. This makes quite a racket, and the only way to quiet it down is to reduce the air supply pressure. Then you get less force, however, and it might not get the job done.

*Engineered air nozzles, such as EXAIR’s Super Air Nozzles, solve this problem by design:

air nozzle flow

The compressed air supply (black arrow) uses the Coanda effect when it exits the series of holes recessed in the array of fins (dark blue arrows.) This serves to entrain an enormous amount of air from the surrounding environment (light blue arrows,) which not only results in a high volume flow rate at minimal consumption, but also makes the resultant air flow very quiet.

EXAIR Super Air Nozzles are quiet, efficient, and easy to get…we maintain inventory of anything you see in the Catalog, all available for same day shipment. If you’d like to know how EXAIR products can be easy on your ears…and your wallet…give me a call!

Russ Bowman
Application Engineer
(513)671-3322 local
(800)923-9247 toll free
(513)671-3363 fax
Visit us on the Web
Follow me on Twitter
Like us on Facebook