EXAIR Back Blow Nozzle: An Overview

In certain applications such as blowing chips or debris out of a pipe or blind hole, it may not be possible to blow forward. The pipe may be too long, making it impossible to push the debris all the way down the pipe or the other end of the pipe may not be open. In either of these scenarios, the Back Blow Nozzle is the right tool for the job. An array of holes around the diameter of the Back Blow Nozzles provides a powerful 360° airflow pattern that will clear out any leftover coolant or chips from the machining process.

m4BB2017_1670x574
Small 1004SS easily clears debris

EXAIR has three different size Back Blow Nozzles; the 1004SS (M4 x .5), the 1006SS (1/4 NPT), and the 1008SS (1” NPT). The 1004SS is recommended for use on pipes as small as ¼” and up to 1”. The 1006SS can be used for a wide range of pipe sizes, from 7/8” up to 4”. The 1008SS nozzle offers the greatest overall force for stubborn or sticky materials stuck to the inside diameter of the pipe. This nozzle is suitable for use in pipes ranging from 2”-16”. As the Back Blow Nozzle will be blowing chips and debris back out of the pipe towards the operator, it is always recommended that a Chip Shield is used. The strong polycarbonate Chip Shield will keep them safe from flying debris and keep you in compliance with OSHA directive 1910.242(b). For visual representation of the performance of the Back Blow Nozzle, take a look at this short video clip that demonstrates its use.

All of EXAIR’s Back Blow Nozzles are available with extensions. For the 1004SS we have extensions from 6”-36”, and from 12”-72” for the 1006SS and 1008SS. The Back Blow Nozzle can also be installed on our VariBlast, Soft Grip, Heavy Duty, and Super Blast Safety Air Guns. With such a wide range of available sizes and configurations, we can tackle just about any internal pipe cleaning application. If you have a process in your facility that may benefit from the use of one of these nozzles, give us a call and get one on order today!

Tyler Daniel
Application Engineer
E-mail: TylerDaniel@exair.com
Twitter: @EXAIR_TD

 

Bad News, Good News, Better News

Recently, I had the pleasure of solving an application for a steel pipe manufacturer. To clean the inside diameters of their freshly-washed pipes, they were using open end blow offs: the ever-popular and easy-to-make, but loud and inefficient crushed-end tubing. I got excited, because this was my first chance to discuss our brand-new Back Blow Nozzle, which is aimed (pun intended) at cleaning inside diameter surfaces. That’s where my story develops a “bad news/good news/better news” pattern…

The bad news: The pipes that need cleaning are up to 20” in diameter…a little too large for our Model 1006SS ¼” NPT Back Blow Nozzle to be completely effective.

EXAIR's brand-new Model 1006 Back Blow Nozzle.
EXAIR’s brand-new Model 1006SS Back Blow Nozzle.

The good news: The user already had a system set up, using the aforementioned “homemade” blow offs, which looked something like this:

Easy to make, hard on your ears...and your air compressor load.
Easy to make, hard on your ears…and your air compressor load.

The better news: They were able to easily adapt their system to install our Model 1120 High Force Super Air Nozzles, which lowered their compressed air consumption as well as the noise level of the operation.

That's the Model 1120 on the far right.
That’s the Model 1120 on the far right.

The moral to this story is, the solution may not be the first one that comes to mind. At EXAIR, that happens all the time. Line Vac questions turn into Air Amplifier answers, and vice versa. Cold Gun calls turn to discussions of Adjustable Spot Coolers. We’ve got three styles of Air Knives to choose from…they’re all perfectly suitable for a wide range of general industrial applications, but they each have their own particular advantages in certain situations. If you have a compressed air product application that you’d like to discuss, EXAIR is your best bet for the most efficient, quietest, quickest solution. It’s like I always say:

Russ Bowman
Application Engineer
Find us on the Web
Follow me on Twitter
Like us on Facebook