The first step to optimizing compressed air systems within an industrial facility is to get a known baseline. To do so, utilizing a digital flowmeter is an ideal solution that will easily install onto a hard pipe that will give live readouts of the compressed air usage for the line it is installed on. There is also an additional feature that we offer on the Digital Flowmeters that can help further the understanding of the compressed air demands within a facility.
The Pressure Sensing Digital Flowmeters are available from 2″ Sched. 40 Iron Pipe up to 8″ Sched. 40 Iron Pipe. As well as 2″ to 4″ Copper pipe. These will read out and with the additional Data Logger or Wireless Capability options record the information. When coupled with the wireless capability an alarm can be set for pressure drops that give live updates on the system as well as permits data review to see trends throughout the day of the system.
Generating a pressure and consumption profile of a system can help to pinpoint energy wasters such as timer-based drains that are dumping every hour versus level based drains that only open when needed. A scenario similar to this was the cause of an entire production line shut down nearly every day of the week for a local facility until they installed flowmeters and were able to narrow the demand location down to a filter baghouse with a faulty control for the cleaning cycle.
If you would like to discuss the best digital flowmeter for your system and to better understand the benefits of pressure sensing, please contact us.
EXAIR Corporation manufactures a variety of engineered compressed air products that have been solving myriad applications in industry for almost 37 years now. In order for them to function properly, though, they have to be supplied with enough compressed air flow, which means the compressed air supply lines have to be adequately sized.
A 20 foot length of 1/4″ pipe can handle a maximum flow capacity of 18 SCFM, so it’s good for a Model 1100 Super Air Nozzle (uses 14 SCFM @80psig) or a Model 110006 6″ Super Air Knife (uses 17.4 SCFM @80psig,) but it’s going to starve anything requiring much more air than those products. Since compressed air consumption of devices like EXAIR Intelligent Compressed Air Products is directly proportional to inlet pressure, we can use the flow capacity of the pipe, the upstream air pressure, and the known consumption of the EXAIR product to calculate the inlet pressure of a starved product. This will give us an idea of its performance as well.
Let’s use a 12″ Super Air Knife, with the 20 foot length of 1/4″ pipe as an example. The ratio formula is:
(P2 ÷ P1) C1 = C2, where:
P2 – absolute pressure we’re solving for*
P1 – absolute pressure for our published compressed air consumption, or C1*
C1 – known value of compressed air consumption at supply pressure P1
C2 – compressed air consumption at supply pressure P2
*gauge pressure plus 14.7psi atmospheric pressure
This is the typical formula we use, since we’re normally solving for compressed air consumption at a certain supply pressure, but, rearranged to solve for inlet pressure assuming the consumption will be the capacity of the supply line in question:
(C2 P1) ÷ C1 = P2
[18 SCFM X (80psig + 14.7psia)] ÷ 34.8 SCFM = 49psia – 14.7psia = 34.3psig inlet pressure to the 12″ Super Air Knife.
…we can extrapolate that the performance of a 12″ Super Air Knife, supplied with a 20 foot length of 1/4″ pipe, will perform just under the parameters of one supplied at 40psig:
Air velocity less than 7,000 fpm, as compared to 11,800 fpm*
Force @6″ from target of 13.2oz total, instead of 30oz*
*Performance values for a 12″ length supplied with an adequately sized supply line, allowing for 80psig at the inlet to the Air Knife.
Qualitatively speaking, if you hold your hand in front of an adequately supplied Super Air Knife, it’ll feel an awful lot like sticking your hand out the window of a moving car at 50 miles an hour. If it’s being supplied with the 20 foot length of 1/4″ pipe, though, it’s going to feel more like a desk fan on high speed.
The type of supply line is important too. A 1/4″ pipe has an ID of about 3/8″ (0.363″, to be exact) but a 1/4″ hose has an ID of only…you guessed it…1/4″. Let’s say you have 20 feet of 1/4″ hose instead, which will handle only 7 SCFM of compressed air flow capacity:
[7 SCFM X (80psig + 14.7psia)] ÷ 34.8 SCFM = 19psia – 14.7psia = 4.3psig inlet pressure to the 12″ Super Air Knife.
Our Super Air Knife performance chart doesn’t go that low, but, qualitatively, that’s going to generate a light breeze coming out of the Super Air Knife. This is why, for good performance, it’s important to follow the recommendations in the Installation Guide:
All Installation Guides for EXAIR Intelligent Compressed Air Products contain recommended air supply line sizes for this very reason. If you have any questions, though, about proper compressed air supply, give me a call.
Visit us on the Web
Follow me on Twitter
Like us on Facebook
The generation of compressed air accounts for approximately 1/3 of all energy costs in an industrial facility. According to the Compressed Air Challenge, about 30% of that compressed air is lost through leaks. This means nearly 10% of your facilities energy costs are simply wasted through poor connections, faulty air valves, improper installation, etc. In addition to simply wasting money, compressed air leaks can also contribute to a variety of other operating losses. A leak can cause a drop in system pressure. When this occurs, end users may not operate as efficiently and has an adverse effect on production. This same drop in system pressure will also cause the equipment to cycle on/off more often, shortening the life of your compressor and other equipment. If the leaks cause an issue in supply volume, it may lead to the belief that more compressor capacity is necessary, further increasing your operating costs.
To put leaks in perspective (assuming energy costs of .10/ kWh), the folks at Compressed Air Challenge put it this way:
A $200/year leak cannot be felt or heard
A $800/year leak can be felt, but not heard
A $1,400/year leak can be felt and heard.
If you walk through your facility, how many leaks can you hear? These are only the REALLY bad ones!! So if we know that a large amount of compressed air is leaking, what do we do about it? ? A proper leak prevention plan is the key to success. Since these leaks are impossible to see and some cannot even be heard, you need a tool to help assist you. EXAIR’s model 9061 Ultrasonic Leak Detector is the right tool for the job. When compressed air leaks through a pipe, it creates an ultrasonic signature due to turbulence. While this sound is not always detectable by the human ear, this meter will allow you to locate leaks up to 20’ away by converting the ultrasonic signature into an audible sound.
The first step will be locating the leaks using an Ultrasonic Leak Detector and tagging them throughout the facility. Don’t let this overwhelm you!! If you have a larger facility, break it up into sections that can be completed in 1 day. This will allow you to decide which areas of the plant should be looked at first. Once you’ve located and tagged all of the leaks, rate them under two separate criteria so that you can prioritize what to fix first. Rate them based on the difficulty that it will take to fix them and also by the severity of the leak. Those that are severe yet easy to fix would make sense to begin fixing first. Those that may require a period of shutdown can be planned to fix at a more appropriate time.
When you’ve had the opportunity to fix them, don’t just forget about it. When new piping is installed, new lines are added, or anything involving compressed air is installed there is the potential for new leaks to develop. Set this as one of your regular PM activities and complete your own compressed air audit once a year. Implementing the process and maintaining it are the keys to your success.
If you have questions about developing a leak program or how to use the Ultrasonic Leak Detector, give us a call. An Application Engineer will be happy to help with the process and recommend some other methods to save on your compressed air supply.
“You can’t manage what you don’t measure” is a well-known axiom in engineering & process improvement circles. We talk to callers every day who are keen on conserving compressed air use in their facilities by making a few tweaks, considering a complete overhaul, or more often, some point in between. Bottom line (literally) is, compressed air isn’t cheap, so small gains in efficiency can add up. And large gains can be complete game-changers…following our Six Steps To Optimizing Your Compressed Air System has resulted in users being able to shut down 50 and 100 HP air compressors, saving thousands of dollar A MONTH in operating costs.
Step #1 is measurement, and that’s where the EXAIR Digital Flowmeter comes in. They’re easy to install, highly accurate, extremely reliable, and available for just about any size pipe used for compressed air distribution. They can output a 4-20mA signal straight from their PCB board, or serial comms (RS485) through an optional control board. USB Data Loggers and Summing Remote Displays have proven to be value-added accessories for data management as well.
If you want to go wireless, we can do that too: using ZigBee mesh network protocol, a radio module is installed in the Digital Flowmeter with wireless gateway to transmit data to an Ethernet connected gateway. The transmitting range is 100 ft (30 meters,) and the data can be passed from one radio module to another, allowing for multiple Digital Flowmeter installations to extend the distance over which they can communicate with the computer you’re using for central monitoring. Advantages include: