EXAIR’s Adjustable Spot Cooler: A Versatile Tool for Your Cooling Needs!

 

If you’re looking at replacing messy coolant mist systems, look no further than the Adjustable Spot Cooler. EXAIR’s Adjustable Spot Cooler incorporates Vortex Tube technology to produce temperatures ranging from -30°F – +70°F. A Vortex Tube works by imparting a rapid spinning motion to the supplied compressed air. This airflow makes its way to the end of the tube where it is forced to abruptly change directions. It is during this change of direction that energy is given off in the form of heat. The hot air then exits the tube from the hot end, while cold air exits the other end of the tube. As the valve is opened to allow more air to exhaust from the hot end, the temperature at the cold end will decrease. At a sound level of just 73 dBA when operated at 100 psig and stock generator installed, this compact cooler will keep your operation cool, clean and dry without causing unnecessarily high noise levels.

3725
Critical tolerances are maintained on plastic parts using the Adjustable Spot Cooler

 

When looking at a Vortex Tube based solution, the variety of options can sometimes be daunting. This is where the versatility of the Adjustable Spot Cooler shines. Through a simple turn of the control knob, you can easily adjust the temperature and cold fraction of the unit. Additionally, the kits come with (2) extra generators (15-H and 30-H) that can be swapped out for the stock generator for more/less cooling power and air consumption. The 15-H generator will deliver up to 1,000 Btu/hr of cooling capacity and the 30-H will provide up to 2,000 Btu/hr of cooling capacity. We have (2) different kits available, the Model 3825 Single Point and the Model 3925 Dual Point Kit. The 3825 is recommended for use in applications where you’re cooling a small surface such as solder joints, hot melts, or drilled plastics. The 3925 system is better served when heat is generated over a larger surface area such as saw blade cooling. The kits use flexible Loc-Line hose to allow you to precisely position the cold airflow onto your target. The Adjustable Spot Cooler provides easy mounting with a swivel magnetic base, allowing you to mount the cooler directly at the most critical point that heat is being generated.

3825_3925 adj spot cooler

If you’re tired of cleaning up your coolant or have an application that requires dry machining, get one of the Adjustable Spot Cooler systems on order today. They’re in stock ready to ship!

Tyler Daniel
Application Engineer
E-mail: TylerDaniel@exair.com
Twitter: @EXAIR_TD

The Adjustable Spot Cooler Is Ideal For Small Parts Cooling

I recently worked with a customer who was trying to cool some small part housings after they leave a wash system. The parts are currently placed in a wash tray where they travel down a conveyor belt and into the washer where they are heated to around 160°F. As the parts exit the washer, the belt is stopped so the parts can be left to cool before an operator places the parts into their dryer system. This cooling process was taking about 15 minutes before the operator was able to safely handle the parts. This cooling delay was negatively affecting their production cycle. They were looking to eliminate the 15 minute cooling cycle by incorporating some type of air cooling system so the parts could be quickly processed to the dryer. They wanted to standardize on a single device as they manufacturer a variety of part shapes with the largest being a valve housing that measures close to 2″ x 2″.

The customer was able to send a few photos of their parts and after reviewing the information sent, I recommended they use our Model # 3925 Adjustable Spot Cooler System with dual point hose kit. Incorporating a Vortex Tube, the Adjustable Spot Cooler is able to produce cold air temperature as low as -30°F, based on ambient supply temperature. The unit features a temperature control valve that allows for simple adjustments of the temperature of the exhausting cold air as well as the volume of air being discharged.  The system includes 2 additional generators which provide more or less airflow volume through the device as well as cooling capacity (Btu/hr.) for even  more control. The dual hose kit separates the cold air into two separate airstreams to provide for a wider coverage area or in this particular case, the customer would be able to treat both sides of the housing for even cooling. The magnetic base makes for easy installation without having to make expensive modifications to their existing setup.

3925 Adjustable Spot Cooler
3925 Adjustable Spot Cooler System – for wider coverage areas with no moving parts to wear out or replace.

EXAIR offers a wide variety of spot cooling products for use in many industrial settings. For help selecting the best product to fit your needs, give me a call, I’d be glad to help.

Justin Nicholl
Application Engineer
justinnicholl@exair.com
@EXAIR_JN

 

 

 

Adjustable Spot Cooler Keeps Band Saw Blade Cool

flir image
Heat camera image of band saw blade heat

We run into interesting applications that require cooling all the time. Here’s an example of a spot cooling application for a tire cutting application that used a FLIR camera to show the heat generated within the band saw blade.

The customer is a world supplier of tires for various vehicles from ATV to construction use. And they have a need to cut tires up for quality control testing as well as R&D purposes. They were looking for a low cost and efficient way to cool the blade without using liquid coolant or water as those methods require implementation of waste handling schemes that this customer did not want to deal with. So, they came to EXAIR as they knew we specialized in cold air cooling products. Specifically, they had interest in model 3925 (Dual Point, Adjustable Spot Cooler System). The dual point hose kit would allow for even cooling on both sides of the band saw blade. After discussing their application details, we agreed that model 3925 would be the best offering we could make to the customer. As we have a band saw in our workshop, I located some rubber material that we had with similar properties to a tire and made some quick tests to determine that in fact, model 3925 allowed for only a modest 5°C rise in temperature. The customer was quite satisfied at our test result and purchased 4 units for their band saws.

Neal Raker, International Sales Manager
nealraker@exair.com

@EXAIR_NR

 

The Adjustable Spot Cooler Provides High Flexibility and Effectiveness

A customer emailed me with some questions about the using the EXAIR spot cooling technology for use on PEEK material being machined in a Swiss Turning machine. Typically, apart from drilling and parting, coolants are not necessary for thermoplastic machining operations.  In order to obtain the best surface finish and tightest tolerances, keeping the cutting area cool is required.  The ideal goal was to provide sub-zero air to the cutting area, while being quiet and easy to operate.  After reviewing the various EXAIR spot cooling products, it was determined that the Adjustable Spot Cooler System would satisfy all of the requirements.

asc-single-point-2
Model 3825 Adjustable Spot Cooler System

The Adjustable Spot Cooler System shown above is capable of producing temperatures from -30°F to room temperature, with just the turn of a knob.  Included in the package are (2) additional generators, which allow for more or less cold air flow rate, depending on the application cooling needs.  With the magnetic base, the system can be easily positioned, and the flexible hose allows for precise aim of the cold air flow. And, sound levels are kept below 75 dBA.

asc_onlathecmyk
Model 3825 Used in a Turning Operation

To recap, the Adjustable Spot Cooler System provides adjustable cold air temperature with the simple turn of a knob, includes additional generators to provide wide ranging flow rates, has a magnetic base to allow for positioning anywhere, on any machine, and has a flexible hose for directing the cold air wherever it is needed.

I would say that it is a Very Adjustable Spot Cooler.

To discuss spot cooling and your application, we ask you to contact EXAIR and one our  Application Engineers can help you determine the best solution.

Brian Bergmann
Application Engineer

Send me an email
Find us on the Web
Like us on Facebook
Twitter: @EXAIR_BB

Quick, Cool, and Quiet – The EXAIR Adjustable Spot Cooler

I recently had the pleasure of assisting a caller with a cooling application. We’ve written before (more than once) about cooling applications & product selection, and I had a very similar conversation with this caller. Since the need was for cooling as quickly as possible to ambient temperature, the caller was keen on talking about Vortex Tubes.

This application entails operators placing small products, by hand, under the cold air flow for rapid cooling.  Now, a Vortex Tube can produce VERY low temperatures…down to -40F…so operator safety had to be addressed.  By keeping the Cold Fraction (the percentage of supply air flow which is directed to the cold end) high, we can also keep the temperature high enough to not present a hazard (i.e., frostbite) but still plenty low enough for effective cooling.

Since sound level was also a concern, we discussed mufflers…with Hot and Cold Mufflers installed on a Medium Vortex Tube (models 3215, 3225, or 3230, which were what we narrowed our discussion to,) a sound level of 81-84 dBA will be produced.  That’s within OSHA’s limits for 8-hour exposure, but isn’t exactly “communication-friendly” for operators that need to talk to each other on a regular basis.

The Model 3825 Adjustable Spot Cooler System incorporates the performance of the three Vortex Tube models that we were talking about into a convenient mag base mounted assembly, fitted with a cold muffler, flexible cold air hose, and additional sound level suppression to 72-74 dBA…which makes a significant difference in areas where operator conversation is critical.

EXAIR's Adjustable Spot Cooler provides cold air, on demand - quiet and easy!
EXAIR’s Adjustable Spot Cooler provides cold air, on demand – quiet and easy!

The temperature control knob allowed them to dial in the optimal cold air flow, keeping the temperature low enough, and flow high enough, for rapid cooling of the parts.

If you’d like to find out just how cool an EXAIR Vortex Tube/Spot Cooling Product can make your application, give me a call.

Russ Bowman
Application Engineer
EXAIR Corporation
Visit us on the Web
Follow me on Twitter
Like us on Facebook

Cooling a Thermal Manikin After a Fire

Not to be persnickety, but there is a difference between mannequins, life size model for displaying or tailoring clothes, and manikins, an anatomical model used for testing and teaching, usually with movable joints. (The enunciation is exactly the same though).  A lab designed a test for thermal protective clothing.  They had a manikin that was 6 feet in height and had 120 copper slug sensors located all over its body. The sensors would record the temperature gradients on the surface of the manikin, representing skin exposure to heat.  They would dress their manikin with thermal protective clothing from head to toe and expose it to intense fires at various temperatures and exposure times.  After each test was completed, they would record the results and cool the manikin to 26 deg. C before they started the next fire test.  These results were used for safety limits to protect wearers from second and third degree burns, very important in keeping firefighters safe.

Fire Suit under test
Fire Suit under test

In their application, they were looking to cool the sensors on the manikin as quickly as they can to increase test cycle rates. Initially they used a “cool down” area fitted with fans to blow air across the manikin.  The problem was that it took too long to cool to the 26 deg. C mark required in their testing protocol.  They decided to manually use an air gun to blow compressed air across the sensors to increase cooling.  This did reduce the cycle time, but because of the force created by the air gun, some sensors would shift and be out of calibration.  This was a huge concern for the test lab.

The design of the copper slug sensor has a small piece of copper set inside a silicone holder. To isolate the copper metal, there are small ruby spheres between the holder and copper slug.  This creates an air gap around the copper slug to help increase sensitivity to temperature changes.  A thermocouple is attached to the back side of the copper slug for analytical measurements.

Adjustable Spot Cooler
Adjustable Spot Cooler

After they discussed their application with me, I suggested the model 3725 Adjustable Spot Cooler. This base unit comes without a magnetic base and hose kit, which makes it lighter in weight. The customer could easily attach it directly to their compressed air line, replacing the air gun that was damaging the sensors.  The Adjustable Spot Cooler incorporates the Vortex Tube which makes standard compressed air into cold air.  With a turn of a knob, they could control the temperature and the velocity of the cold air.  This feature was key in determining just the right amount of force to not affect the calibration of the sensors.  An added benefit of the Adjustable Spot Cooler is if you reduce the amount of outlet cold air, the temperature will decrease even more.  This feature allowed the customer to reach their target much more quickly and without damaging the sensors.

If you need to cool things down in your application, you can contact an Application Engineer at EXAIR. We have many different styles and combinations of Vortex Tubes and Spot Coolers to give you the right form of cooling, whether it is a mannequin or a manikin.

John Ball
Application Engineer
Email: johnball@exair.com
Twitter: @EXAIR_jb

 

DDI-2007-Burning Man by Interpretive Arson.  Common License.

Adjustability=Flexibility=Wide Ranging Performance

Recently, I moved into a new house, and it didn’t have bathroom vent fans.  In order to prevent mold and mildew growth from the humid shower air; we decided to install them ourselves.  Going to the local home goods store, we were faced with a wall of options, with factors such as noise level, CFM rating and of course price.  Going over the myriad of possibilities was headache inducing and of course, the bathroom size was borderline between a small and mid-size unit. The decision came down to – pay more and oversize it or risk installing an undersized unit.  If only they made a unit to cover a wide variety of conditions.

Here at EXAIR, we make many types of Intelligent Compressed Air Products.  Many times, when we are talking to customers, the right size or performance needed isn’t quite clear.  Fortunately, many of the products we make are flexible, and allow for adjustability and increased range of performance to best match the specific need of the application.

For example, The Super Air Knives and Super Air Wipes have available Shim Sets to increase or decrease the air gap and change the force and flow.  The shims are easily installed, and come in a wide choice of sizes. Super Air Knives are available, from stock, in aluminum, 303SS, 316SS, and PVDF. Super Air Wipes are made from aluminum or 303 SS.

The Super Air Amplifiers also have available patented Shim Sets to fix the air flow at a predetermined setting. Adjustable Air Amplifiers have an infinitely adjustable air gap which can easily be set to match the application needs if a predetermined flow is not preferred. Adjustable Air Amplifiers also have a smaller footprint than Super Air Amplifiers and can also use the aforementioned shims to preset the air flow in applications where space is limited. These are available in 303 stainless steel and aluminum. We also have a high temperature option.

adjustable Air Amplifier
Adjustable Air Amplifier

Within our already enormous and flexible Air Nozzles & Jets product line, the Flat Super Air Nozzles have available Shim Sets to provide the ability to adjust the force and flow for blowoff or cleaning operation.  The model 1009 Adjustable Air Nozzle has an adjustable gap setting, allowing you to “tune in” the force and flow to meet the application requirement.  Also, the Adjustable Air Jet provides an adjustable gap setting to control the air flow performance. Flexibility also comes from the available materials of zinc/aluminum, aluminum, 303SS, 316SS and PEEK thermoplastic.

For vacuum generation, the Adjustable E-Vac allows for the vacuum and flow rate to be easily adjusted.  With a simple turn of the unit, the vacuum and flow levels can be changed to overcome porosity and increase or decrease the lifting power.

Adjustable EVac
Adjustable E-Vac

There are several other Intelligent Compressed Air Products that EXAIR manufactures that offer the adjustability and flexibility, such as Vortex Tubes and Adjustable Spot Coolers.

If only EXAIR manufactured bathroom fans, I could have ensured making the right choice and be able to match the performance to exactly meet my application needs.

Brian Bergmann
Application Engineer
Find us on the Web
Like us on Facebook